10KENG3EA Delta

HIGH PERFORMANCE SNAP-IN VV DD EE OROR SERIES FILTERS INTRODUCTIONS SPECIFICATIONS 1. Specially designed with ground choke providing most effective 1. Maximum leakage current each EMI suppression for high frequency noise (ranged 5MHz-25MHz). line-to-ground 115VAC 60Hz: 0.20mA 2. Bleeder resistor can be added with suffix- on part numbers. 250VAC 50Hz: 0.40mA 3. With optional Y capacitor from 100pF to 3300pF. 2. Hipot rating (one minute) 4. All part numbers are UL recognized, CSA certified and VDE approved. line-to-ground: 2250VDC 5.Optional side snap-in mounting clip type with suffix (H) on part numbers. line-to-line: 1450VDC for 03/06/10KENG3SA series. 3. Operating frequency: 50/60Hz 4. Rated voltage: 115/250VAC COMPONENTS PART NO. L (mH) Cx (uF) Cy (pF) Lg (uH) 03KENG3EA/03KENW3EA 3.1 L N 08KENG3EA/08KENW3EA 0.8 * G 10KENG3EA/10KENW3EA 0.4 0.1 2200 100 ** 03KENG3SA/03KENW3SA 3.1 1.22 0.02 06KENG3SA/06KENW3SA 0.8 31.5 0.5 10KENG3SA/10KENW3SA 0.4 VDE approved to 6A 250V. * UL, CSA & VDE approved to 9A 115/250 VAC. ** MINIMUM INSERTION LOSS IN dB R0.08MAX. R2.0MAX. +0.012 COMMON MODE (L-G) IN 50 OHM SYSTEM 1.12-0 +0.3 0.0315~0.063 28.45-0 0.8~1.6 FREQUENCY-MHz PART NO. SUGGESTED MOUNTING CUTOUT .15 .50 1.0 5.0 10 30 1.12MAX. 03KENG3EA/03KENW3EA 15 20 25 40 40 45 28.4MAX. G3SA 08KENG3EA/08KENW3EA 10 15 20 35 40 50 10KENG3EA/10KENW3EA 7 12 18 30 30 50 03KENG3SA/03KENW3SA 15 20 25 40 40 40 Suggested thickness of mounting panel is from 0.0315 (0.8) to 0.063 (1.6) inch(mm) of mounting cutout 06KENG3SA/06KENW3SA 7 15 20 35 40 40 10KENG3SA/10KENW3SA 4 12 18 30 30 45 L N DIFFERENTIAL MODE (L-L) IN 50 OHM SYSTEM G 03KENG3EA/03KENW3EA 5 12 15 40 50 45 08KENG3EA/08KENW3EA 5 10 15 45 40 50 1.22 0.02 31.5 0.5 10KENG3EA/10KENW3EA 4 12 18 30 30 50 03KENG3SA/03KENW3SA 10 20 35 40 45 40 06KENG3SA/06KENW3SA 10 25 40 35 40 40 10KENG3SA/10KENW3SA 10 25 35 30 30 45 R0.08MAX. 1.12MAX. R2.0MAX. 28.4MAX. +0.012 1.12-0 +0.3 0.0315~0.063 ELECTRICAL SCHEMATIC 28.45-0 0.8~1.6 SUGGESTED MOUNTING CUTOUT L L Cy L R Cx L I O L WIRE LENGTH : 4.0 MIN. N A E D Cy W3EA N N G G Lg R: 1M /-R ONLY L N G MECHANICAL CONSTRUCTION 1.22 0.02 31.5 0.5 R0.08MAX. R2.0MAX. +0.012 1.12-0 +0.3 0.0315~0.063 G3EA W3EA 28.45-0 0.8~1.6 INCH UNIT: SUGGESTED MOUNTING CUTOUT mm 1.12MAX. 28.4MAX. G3EA 2-12 IEC INLET FILTERS 1.89MAX. 1.66MAX. 1.89MAX. 48.0MAX. 0.945 0.02 0.945 0.02 42.16MAX. 0.945 0.02 48.0MAX. +0.04 +0.04 +0.04 24.0 0.5 24.0 0.5 24.0 0.5 - 0.14-0.02 - 2.32 MAX. 0.14 0.02 4.0MIN. 1.97 0.04 2.1MAX. 0.14 0.02 59.0 MAX. +1.0 100.0MIN. 50.0 1.0 +1.0 53.4MAX. +1.0 3.6-0.5 3.6-0.5 3.6-0.5 0.84 MAX. 21.3 MAX. 0.862 0.004 0.862 0.004 0.862 0.004 21.90 0.1 21.90 0.1 21.90 0.1 21.3MAX. 0.84MAX. 21.4MAX.