ASSY USED ON:
CODE 54 - HEAT SHRINK BOOT BACKSHELL
201M116-19C-D
SERIES
DASH NUMBER (TABLE 1)
MATERIAL
REFER TO CH00-0250-004
FINISH
REFER TO CH00-0250-004
MODIFICATION CODE
REFER TO CH00-0250-004 2
NOTES:
1. THIS PRODUCT IS DESIGNED TO TERMINATE A HEAT SHRINKABLE LIPPED
BOOT TO A CONNECTOR.
2. FOR ADDITIONAL DIMENSIONS, ORDERING INFORMATION AND MODIFICATIONS,
SEE CH00-0250-004.
3. ADAPTOR TO BE PERMANENTLY MARKED/BAGGED AND LABELLED WITH CODE
IDENTIFICATION NUMBER AND PART NUMBER. (e.g. 06090-201M112-19A).
4. BACKSHELL MATES TO MIL-C-81703, SERIES III, MS3424, MS3446, MS3464, MS3467, MS3468, CLASS E & L
5. BACKSHELL MATES TO MIL-C-5015G, MS3400 SERIES, CLASS D, E, K, L, U & W,
MS3400, MS3401, MS3404, MS3406,MS3450, MS3451, MS3454, MS3456, MS3470, MS3471, MS3472,
MS3474, MS3475, MS3476. MIL-C-83723, SERIES II, CLASS A & L. MIL-C-83723,
SERIES I & III, CLASS A, G, K, R & S: M83723/1, /2, /3, /4, /5, /6, /7, /8, /13,
/14, /36, /37, /38, /40, /41, /42, /43, /48, /49, /65, /66, /67, /68, /69,
/70, /71, /72, /73, /74, /75, /76, /77, /78, /82, /83, /84, /85, /86, /87, /91, /92, /95, /97, /98,
(MS3155 CONTROLLED INTERFACE).
6. WHEN MODIFICATION IS SPECIFIED, COUPLING NUT SHALL HAVE 3 WIRE HOLES,
120 APART.
DATE
3RD ANGLE
DRAWN K.WINCZURA
TITLE:
PROJECTION
19/02/2015
NOT TO
CHECKED 19/02/2015 SCALE
HEAT SHRINK BOOT BACKSHELL
UNLESS OTHERWISE SPECIFIED
APPROVED
K.SHEPPARD 03/03/2015
ALL DIMENSIONS IN MILLIMETRES
GENERAL TOL
LINEAR +/-0,25MM
APPROVED H.SMITH 20/08/2015
ANGULAR +/- 1
REVISIONS
LTR DATE APPROVED
DESCRIPTION
MIL-DTL-26482 SERIES II / MIL-DTL-83723 SERIES I & III
J2 26/03/2015 H.SMITH
REVISED PER ECO-15-004707
K REVISED PER ECO-15-011999 20/08/2015
H.SMITH
TE CONNECTIVITY - POLAM CO LTD RESERVES THE RIGHT TO AMEND THIS DRAW ING DRAWING NO: DRAWING REV: SHT
TE CAGE CODE: 06090 AND THE INFORMATION SET FORTH HEREON AT ANY TIM E. USERS SHOULD
INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION.
201M1XX K 1
POLAMCO/TE CAGE CODE: U5792ASSY USED ON:
A-A
E REF.
26,90 MAX
A
G
3,50
STAINLESS
STEEL
TEETH VIEW
PART MARK MEDIUM DIAMOND
HERE KNURL
6
A
TABLE 1
BASE PART SHELL A B Z Y X E
G
+0,00/-0,50 +0,20/-0,00
NUMBER SIZE THREAD MAX MIN REF.
201M103 03 9/16 -24UNEF 17,0 6,6 13,5 1,12 10,5 28,0
15,6 6,6 13,5 1,12 10,5 28,0
201M108 08 1/2 -20UNF
201M110 10 5/8 -24UNEF 18,6 9,3 15,4 1,12 10,5 28,0
21,7 12,8 19,7 1,12 10,5 28,0
201M112 12 3/4 -20UNEF
201M114 14 7/8 -20UNEF 24,9 14,7 21,3 1,12 10,5 28,0
28,2 17,8 24,5 1,12 10,5 28,0
201M116 16 1 -20UNEF
201M118 18 30,9 19,8 26,5 1,12 10,5 28,0
1 1/16 -18UNEF
201M120 20 1 3/16 -18UNEF 34,1 23,0 30,9 1,75 10,5 28,0
37,3 26,2 34,4 1,75 10,5 28,0
201M122 22 1 5/16 -18UNEF
201M124 24 1 7/16 -18UNEF 40,4 29,1 36,8 1,75 10,5 28,0
50,0 35,1 43,4 1,75 10,5 28,0
201M128 28 1 3/4 -18UNS
201M132 32 2 -18UNS 56,3 41,3 48,7 2,20 14,5 32,3
62,7 46,8 55,1 2,20 14,5 32,3
201M136 36 2 1/4 -16UN
69,0 52,2 61,0 2,20 14,5 32,3
201M140 40 2 1/2 -16UN
201M144 44 2 3/4 -16UN 75,4 58,7 67,5 2,20 14,5 32,3
81,7 65,1 73,8 2,20 14,5 32,3
201M148 48 3 -16UN
201M161 61 1 1/2 -18UNEF 42,0 30,1 38,8 1,75 10,5 28,0
DATE
3RD ANGLE
DRAWN K.WINCZURA
TITLE:
PROJECTION
19/02/2015
NOT TO
CHECKED 19/02/2015 SCALE
HEAT SHRINK BOOT BACKSHELL
UNLESS OTHERWISE SPECIFIED
APPROVED
K.SHEPPARD 03/03/2015
ALL DIMENSIONS IN MILLIMETRES
GENERAL TOL
LINEAR +/-0,25MM
APPROVED H.SMITH 20/08/2015
ANGULAR +/- 1
REVISIONS
LTR DATE APPROVED
DESCRIPTION
MIL-DTL-26482 SERIES II / MIL-DTL-83723 SERIES I & III
J2 26/03/2015 H.SMITH
REVISED PER ECO-15-004707
K REVISED PER ECO-15-011999 20/08/2015
H.SMITH
TE CONNECTIVITY - POLAM CO LTD RESERVES THE RIGHT TO AMEND THIS DRAW ING DRAWING NO: DRAWING REV: SHT
TE CAGE CODE: 06090 AND THE INFORMATION SET FORTH HEREON AT ANY TIM E. USERS SHOULD
INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION.
201M1XX K 2
POLAMCO/TE CAGE CODE: U5792
B
A THREAD
XXXX
Z
X
Y