GLS85LS1002P / 1004P / 1008P Industrial Grade SATA NANDrive Fact Sheet 04.000 October 2016 Features Industry Standard Serial ATA (SATA) Host Integrated Voltage Detector Interface - Detects supply voltage fluctuations and 1) generates reset during power-up and power- - SATA 1.5 Gb/s or SATA 3.0 Gb/s down to prevent inadvertent writes - ATA/ATAPI-8 compliant Supports SMART Commands - Supports 48-bit address feature set Expanded Data Protection Performance - Sequential data read: - Added data security through user-selectable protection zones Up to 70 MByte/sec* - Sequential data write: 20-Byte Serial Number Up to 60 MByte/sec* - Factory pre-programmed 10-Byte unique ID * measured using 128 KByte transfer size - User-programmable 10-Byte ID Power Management Robust Built-in ECC - 3.3V and 1.2Vpower supply NAND Configuration - Host SATA interface power management - 1 bit per cell (SLC) - Immediate disabling of unused circuitry Industrial Temperature Range without host intervention - -40C to 85C 2) Power Specifications FBGA package - Active mode: - 14.0 mm x 24.0 mm x 1.95 mm, 145-ball, 750mW typical (GLS85LS1008P) 1.0 mm ball pitch, FZJE 560mW typical (GLS85LS1004P) All Devices are RoHS Compliant 450mW typical (GLS85LS1002P) - Idle / Standby mode: 210mW typical 1) Current product revision supports SATA Revision 1.x with host transfer rate of up to 1.5 Gb/s (i.e. SATA 1.5 Gb/s). - Sleep mode: 70mW typical SATA 3.0 Gb/s refers to SATA Revision 2.x and will be supported by our planned future product revisions. 2) For management of the Sleep Mode, refer to SATA NANDrive Application Design Guide. Product Description The GLS85LS1002P / 1004P / 1008P Industrial Grade The integrated NAND flash controller with built-in SATA NANDrive devices (referred to as SATA advanced NAND management firmware NANDrive in this fact sheet) are fully integrated solid communicates with the host through the standard state drives. They combine an advanced Greenliant SATA protocol. It does not require any additional or NAND controller and 2, 4 or 8 GByte of NAND flash in proprietary software such as the Flash File System a multi-chip package. These products are ideal for (FFS) and Memory Technology Driver (MTD). embedded and portable applications that require SATA NANDrive is pre-programmed with a 10-Byte smaller form-factor and more reliable data storage. unique serial ID and has the option of programming SATA-interface solid state mass storage technology is an additional 10-Byte serial ID for even greater widely used in portable and industrial computers, set- system security. top boxes, multi-functional printers, point-of-sales SATA NANDrives advanced NAND management terminals, video and audio recorders, medical technology enhances data reliability and security, instruments and car infotainment systems. improves endurance and accurately estimates the SATA NANDrive is a single device, solid state drive remaining life of the NAND flash devices. This (SSD) that provides the functionality and compatibility innovative technology combines robust NAND of a complete SATA hard disk drive (HDD) in a 14 mm controller hardware error correction capabilities with x 24 mm BGA package for easy, space saving advanced wear-leveling algorithms and bad block mounting to a system motherboard. These products management to significantly extend the life of the surpass traditional storage in their small size, security, product. reliability, ruggedness and low power consumption. SATA NANDrive devices are offered in a 145-ball BGA, 1 mm ball pitch package. These specifications are subject to change without notice. 10/19/2016 2016 Greenliant Systems 1 S71432-F GLS85LS1002P / 1004P / 1008P Industrial Grade SATA NANDrive Fact Sheet 04.000 October 2016 1.0 GENERAL DESCRIPTION Each SATA NANDrive contains an integrated SATA NAND flash memory controller and up to eight discrete NAND flash die in a BGA package. Refer to Figure 2-1 for the SATA NANDrive block diagram. 1.1.4 Embedded Flash File System 1.1 Optimized SATA NANDrive The embedded flash file system is an integral part of The heart of SATA NANDrive is the SATA NAND flash SATA NANDrive. It contains MCU firmware that memory controller which translates standard SATA performs the following tasks: signals into flash media data and control signals. The following components contribute to SATA NANDrives 1. Translates host side signals into flash media operation. writes and reads 1.1.1 Microcontroller Unit (MCU) 2. Provides flash media wear leveling to spread the flash writes across all memory address space to The MCU translates SATA commands into data and increase the longevity of flash media control signals required for flash media operation. 3. Keeps track of data file structures 1.1.2 Internal Direct Memory Access (DMA) 4. Manages system security for the selected SATA NANDrive uses internal DMA allowing instant protection zones data transfer from/to buffer to/from flash media. This 1.1.5 Error Correction Code (ECC) implementation eliminates microcontroller overhead associated with the traditional, firmware-based High performance is achieved through optimized approach, thereby increasing the data transfer rate. hardware error detection and correction. 1.1.3 Power Management Unit (PMU) 1.1.6 Serial Communication Interface (SCI) The PMU controls the power consumption of SATA The Serial Communication Interface (SCI) is designed NANDrive. The PMU dramatically reduces the power for error reporting. During the product development consumption of SATA NANDrive by putting the part of stage, it is recommended to provide the SCI port on 3) the PCB to aid in design validation. the circuitry that is not in operation into sleep mode. 1.1.7 Multi-tasking Interface The Flash File System handles inadvertent power interrupts and has auto-recovery capability to ensure The multi-tasking interface enables fast, sequential SATA NANDrive firmware integrity. For regular power write performance by allowing concurrent Read, management, the host must send a Program and Erase operations to multiple flash media. STANDBY IMMEDIATE (E0h), IDLE IMMEDIATE (E1h), STANDBY (E2h) or IDLE (E3h) command and 1.2 SMT Reflow Consideration wait for command ready before powering down SATA NANDrive. The SATA NANDrive family utilizes standard NAND 3) For management of the Sleep Mode, refer to SATA flash for data storage. Because the high temperature NANDrive Application Design Guide. in a surface-mount soldering reflow process may alter the content on NAND flash, it is recommended to program SATA NANDrive after the reflow process. 1.3 Advanced NAND Management SATA NANDrives integrated controller uses advanced wear-leveling algorithms to substantially increase the longevity of NAND flash media. Wear caused by data writes is evenly distributed in all or select blocks in the device that prevents hot spots in locations that are programmed and erased extensively. This effective wear-leveling technique results in optimized device endurance, enhanced data retention and higher reliability required by long-life applications. These specifications are subject to change without notice. 10/19/2016 2016 Greenliant Systems 2 S71432-F