CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Radial Lead TM NPCAP -PSESeries PSE Super low ESR, high ripple current capability Endurance : 20,000 hours at 105 Longer life Rated voltage range : 2.5 to 6.3Vdc Downsized Solvent resistant type (see PRECAUTIONS AND GUIDELINES) PSC RoHS2 Compliant Halogen Free SPECIFICATIONS Items Characteristics Category -55 to +105 Temperature Range Rated Voltage Range 2.5 to 6.3Vdc Capacitance Tolerance 20% (M) (at 20, 120Hz) Leakage Current I=0.2CV or 500A, whichever is greater *Note Where, I : Max. leakage current (A), C : Nominal capacitance (F), V : Rated voltage (V) (at 20 after 2 minutes) Dissipation Factor 0.10 max. (at 20, 120Hz) (tan ) Low Temperature Z(-25)/Z(+20)1.15 Characteristics Z(-55)/Z(+20)1.25 (at 100kHz) (Max.Impedance Ratio) Endurance The following specications shall be satised when the capacitors are restored to 20 after the rated voltage is applied for 20,000 hours at 105. Appearance No signicant damage Capacitance change 20% of the initial value D.F. (tan ) 150% of the initial specied value ESR 200% of the initial specied value Leakage current The initial specied value Bias Humidity Test The following specications shall be satised when the capacitors are restored to 20 after subjecting them to DC voltage at 60, 90 to 95% RH for 1,000 hours. Appearance No signicant damage Capacitance change 20% of the initial value D.F. (tan ) The initial specied value ESR The initial specied value Leakage current The initial specied value Surge Voltage Test The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specied at 105 for 30 seconds through a protective resistor(R=1k) and discharge for 5 minutes 30 seconds. Rated voltage (Vdc) 2.5 4.0 6.3 Surge voltage (Vdc) 2.9 4.6 7.2 Appearance No signicant damage Capacitance change 20% of the initial value D.F. (tan ) The initial specied value ESR The initial specied value Leakage current The initial specied value Failure Rate 0.5% per 1,000 hours maximum (Condence level 60% at 105) *Note : If any doubt arises, measure the leakage current after the following voltage treatment. Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105. DIMENSIONS mm Terminal Code : E Coated Case Size code F08 MARKING D 6.3 EX) 2.5V820F d 0.6 F 2.5 6D6 E D + D 0.5max. 820 L L+1.5max. V 2.5 L 15min. 4min. Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. CAT. No. E1001U D d F0.5CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Radial Lead TM NPCAP -PSESeries PART NUMBERING SYSTEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 A PSE 2R5 E AA 5 6 1 M F 0 8 S Supplement code Size code Capacitance tolerance code Capacitance code (ex. 820F:821) Lead formingTaping code Terminal code Voltage code (ex. 2.5V:2R5, 4V:4R0, 6.3V:6R3) Series code Category Please refer toProduct code guide (conductive polymer type STANDARD RATINGS WV Cap Case size ESR Rated ripple current Part No. (Vdc) (F) D L(mm) (m max./20 , 100k to 300kHz) (mArms/105 , 100kHz) 2.5 820 6.3 8 7 5,000 APSE2R5E 821MF08S 4 560 6.3 8 7 5,000 APSE4R0E 561MF08S 470 6.38 8 4,700 APSE6R3E471MF08S 6.3 560 6.38 8 4,700 APSE6R3E561MF08S : Enter the appropriate lead forming or taping code. RATED RIPPLE CURRENT MULTIPLIERS Frequency Multipliers Frequency Hz 120 1k 10k 50k 100k to 500k Radial lead type 0.10 0.35 0.60 0.80 1.00 Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. CAT. No. E1001U