8 7 6 5 4 3 2 1
NOTES
TM
1.
REGULATORY INFORMATION:
* MILITARY (WITH 3M'S N3518 POLARIZING KEY)
3M THREE-WALL HEADER, 3000 SERIES
ROHS COMPLIANT. SEE THE
AND CENTERBUMP POLARIZATION.
REGULATORY INFORMATION
.100" X .100" LATCH/EJECTOR, STRAIGHT AND RIGHT ANGLE
* LOW PROFILE.
APPENDIX (RIA) IN THE
* OPTIONAL EJECTOR LATCHES.
ROHS COMPLIANC SECTION
* MOUNTING HOLES FOR SECURING HEADER TO BOARD.
OF WWW.3MCONNECTORS.COM FOR
* THREE WALL SHROUD PROVIDES DESIGN FLEXIBILITY.
COMPLIANCE INFORMATION.
DIM.
* SOLDER TAIL AND WRAP TAIL OPTIONS.
* OPTIONAL POLARIZING POSTS AVAILABLE.
2 IN THE EVENT OF CONFLICT
* HIGH TERMERATURE INSULATOR SUITABLE FORNO LEA
BETWEEN THIS DATA AND THAT
SOLDERING OPERATIONS.
CONTAINED IN THE PRODUCT
D .68 D
* SUITABLE FOR REFLOW SOLDERING USINGPASTE IN HOL
SPECIFICATION, THE PRODUCT
TECHNIQUES.
SPECIFICATION TAKES PRECEDENT.
17.4
3 NOTCHES A & C WILL ACCOMODATE
3M POLARIZING KEY: N3518).
4 MOUNTING HARDWARE:
2
FROM SOLDER SIDE OF PC BOARD
PHYSICAL:
-X0XX USE #4-24 THREAD CUTTING SCREW
INSULATOR:
(3M PART #3341-5) WITH
HEADER WITHOUT LATCH EJECTOR
MATERIAL: GLASS FILLED POLYESTER (PCT)
.116 [2.95] MOUNTING HOLE.
FLAMMABILITY: UL94V-0
FOR RIGHT ANGLE VERSION ONLY:
COLOR: BLACK
#2-56 BOLT AND NUT (3M PART
CONTACT:
#3341-6) WITH .106 [2.69]
MATERIAL: COPPER ALLOY
.010
.424
MOUNTING HOLE MAY BE USED.
PLATING:
10.77 0.25
UNDER PLATING: 100 [2.54 m] NICKEL-OVERALL THE RECOMMENDED PCB HOLE SIZE
5
WIPING AREA: 30 [0.76 m] AVG. GOLD FOR THE KINKED TAIL POSITIONS
SOLDER TAILS: 200 [5.08 m] TIN LEAD OR MATTE TIN (SEE ORDERING INFORMATION) ON THE .112 SOLDER TAIL
MARKINGS: 3M LOGO, PART IDENTIFICATION NUMBER AND ORIENTATION TRIANGLE CONNECTOR IS .035 .002.
(SEE K2 VERSION).
.97
.08
2.0 2
ELECTRICAL:
24.7
CURRENT RATING: 5.00A, 1 CONTACT POWERED
3.00A, 6 CONTACTS POWERED
C C
1.75A, ALL CONTACTS POWERED
RATING CONDITIONS: EIA-364-070 METHOD 2, 30 C MAXIMUM
.37 9.5
TEMPERATURE RISE, 20% DERATED. REFERENCE APPROPRIATE
-X2XX
3M PRODUCT SPECIFICATION FOR DETAILED CURRENT DERATING
HEADER WITH SHORT LATCH EJECTOR
CURVES.
9
FOR 3M SOCKETS WITHOUT STRAIN RELIEF
INSULATION RESISTANCE: >1 X 10 AT 500 V
DC
WITHSTANDING VOLTAGE: 1,000V AT SEA LEVEL
RMS
2
ENVIRONMENTAL:
.573 .010
TEMPERATURE RATING: -55 C TO 105 C
PROCESS RATING: 260 C, PER J-STD-020C, SINGLE PASS
0.25
14.55
MOISTURE SENSITIVITY LEVEL: 1 (PER J-STD-020C)
1.07
.08
2.0
27.2
B B
.46 11.7
-X3XX
HEADER WITH LONG LATCH EJECTOR
FOR 3M SOCKETS WITH STRAIN RELIEF
ORDERING INFORMATION
X3XXX-XXXXXX
H 60056 MAR 06,2015 JNC RS
N= HIGH TEMP BLACK (PCT)/(RB PLATING REQ'D) PLATING:
REVISE ORDERING
NUMBER
BLANK= (UB PLATING)
RB = 30 [0.76 m] GOLD AND 200 [5.08 m] MATTE TIN
DIMENSIONS: INCHES [MM]
G 56068 AUG 05,2014 JNC RS
(APP. E1 & C1 APPLY)
[MM] IS REF. ONLY
3M PART NUMBER:
REVISED AND REDRAWN
UB = 30 [0.76 m] GOLD AND 200 [5.08 m]
(SEE TABLE 1)
DESIGN REFERENCE NEXT ASSEMBLY REV ECO ISSUE DATE AND DESCRIPTION DRFT CHKD
TIN LEAD (APP. E3 & C2 APPLY)
ACCESS DRFT DATE MFG DATE
CODES CASTIGLIONE AUG 05,2014
CHKD DATE APPVL DATE
PIN CONFIGURATION: TAIL:
R. SCHERER SEP 05,2014
A A
1 = RIGHT ANGLE SOLDER TAILS 02 = FOR .062 [1.57] THICK BOARD
DIVISION DIVISION CODE
C
3M COPYRIGHT 2015
3M Center
Interconnect Solutions EMSD
This document and the information it contains are
2 = STRAIGHT SOLDER TAILS 03 = FOR .094 TO .125 [2.39 TO 3.18] THICK BOARD
3M property and may not be reproduced or further
St. Paul,
SCALE TOLERANCES
DO NOT distributed without 3M permission, or used or
K2 = KINKED FOR .062 [1.57] THICK BOARD
EXCEPT AS MN 55144
disclosed other than for 3M authorized purposes.
2
SCALE
All rights reserved.
NOTED
1
DRAWING
TITLE
INCHES
LATCH/EJECTOR SYSTEM:
3M ELECTRONIC MATERIALS SOLUTIONS DIVISION
.0
HEADER, 3-WALL, .100
.00 .01
0 = NO LATCH/EJECTOR INSTALLED
INTERCONNECT SOLUTIONS
.000 .005
2 = SHORT ROLL PIN LATCH/EJECTORS
8 7 6 5 4 3 2 1
TM
3M THREE-WALL HEADER, 3000 SERIES
DIM. .28
.100" X .100" LATCH/EJECTOR, STRAIGHT AND RIGHT ANGLE
7.1
.100
.020
.15
2.54 0.51
3.8
.100
D D
2.54
.25
.31
.025 .002
.002
.025
6.4
7.9
0.05
0.64
0.64 0.05
SQ. TYP.
SQ. TYP.
2X .100
POSITION #1
2.54
SEE NOTE 4
DIM.
DIM.
.24
TYP.
.24
6.2
6.2
NOTCH
.100
(SEE TABLE 1 & NOTE 3)
.30
.30
7.5
2.54
.16
NOTCH
7.5
(SEE TABLE 1)
POSITION 1
4.1
ORIENTATION
TRIANGLE
NOTCH
DIM. .010 (SEE TABLE 1 & NOTE 3)
A B
.049
DIM. .010
TAIL
TAIL
DIM.
C C
1.24
TYP.
SECTION B-B
SECTION A-A
(RIGHT ANGLE VERSION)
(STRAIGHT VERSION)
.68
.19
17.4
4.8
.12 3.0
2X .100
A
B
.020 0.51
2.54
SEE NOTE 4
TABLE 1 .20
DIM.
PIN 3M PART POLARIZING PIN
5.1
DIM. DIM. DIM. DIM.
QTY. NUMBER NOTCHES QTY.
B B
DIM.
10 3793 1.26 [32.1] 1.105 [28.04] .865 [21.97] .71 [18.0] BC 10
14 3314 1.46 [37.2] 1.305 [33.12] 1.065 [27.05] .91 [23.1] BC 14
16 3408 1.56 [39.7] 1.405 [35.66] 1.165 [29.59] 1.01 [25.6] ABC 16
20 3428 1.76 [44.8] 1.604 [40.74] 1.365 [34.67] 1.21 [30.7] ABC 20
26 3429 2.06 [52.4] 1.905 [48.36] 1.665 [42.29] 1.51 [38.3] ABC 26
34 3431 2.46 [62.6] 2.305 [58.52] 2.065 [52.45] 1.91 [48.5] ABC 34
40 3432 2.76 [70.2] 2.605 [66.14] 2.365 [60.07] 2.21 [56.1] ABC 40
50 3433 3.26 [82.9] 3.105 [78.84] 2.865 [72.77] 2.71 [68.8] ABC 50
60 3372 3.76 [95.6] 3.605 [91.54] 3.365 [85.47] 3.21 [81.5] ABC 60
64 3764 3.96 [100.7] 3.805 [96.62] 3.565 [90.55] 3.41 [86.6] ABC 64
H 60056 MAR 06,2015 JNC RS
REVISE ORDERING
NUMBER
G 56068 AUG 05,2014 JNC RS
REVISED AND REDRAWN
DESIGN REFERENCE NEXT ASSEMBLY REV ECO ISSUE DATE AND DESCRIPTION DRFT CHKD
ACCESS DRFT DATE MFG DATE
CODES CASTIGLIONE AUG 05,2014
TABLE 2
CHKD DATE APPVL DATE
R. SCHERER SEP 05,2014
3M PART
A A
DIVISION DIVISION CODE
C
3M COPYRIGHT 2015
NUMBER CONTACT TAIL DIM. PIN CROSS SECTION DIM.
3M Center
Interconnect Solutions EMSD
This document and the information it contains are
3M property and may not be reproduced or further
St. Paul,
SUFFIX
SCALE TOLERANCES
DO NOT distributed without 3M permission, or used or
EXCEPT AS MN 55144
disclosed other than for 3M authorized purposes.
4
SCALE
All rights reserved.
NOTED
1
DRAWING
-1XX2 TITLE
.062 [1.57] THICK DIM. DIAGONALS CORNER RADII .035+/-.003 [.89]
INCHES
.112 [2.84]
.0
PC BOARD .0245+/-.0005 [.622] .028+/-.001 [.71] .0075 REF. [.191] SEE NOTE 5
HEADER, 3-WALL, .100
.00 .01
-2XX2
.000 .005
X .100 LATCH/EJECTOR,
THIRD ANGLE PROJECTION .0000
.094 [2.39] TO
-1X03
MILLIMETERS
.125 [3.18] THICK .155 [3.94] .0245+/-.0005 [.622] .028+/-.001 [.71] .0075 REF. [.191] .035+/-.003 [.89] INTERPRET PER
STRAIGHT & RA
ASME Y14.5 - 2009 0
-2X03 PC BOARD
.0 .3
CAGE SIZE DRAWING NO. REV.
MAX SURFACE ROUGHNESS
.00 .13
NUMBER
ALL SURFACES .000 78-5100-0771-5 H
MODEL DET.
MARKED ONLY
ANGLES
3000 SERIES YES NO SHT 2 OF 4
LISTS
8 7 6 5 4 3 2 1
78-5100-0771-5 H
DRAWING NUMBER REVISION
Imaged: H.1 3/6/2015 12:53 PM UTC-06:00