4 3 2 1 NOTES 1. DIMENSIONS ARE IN MILLIMETERS. TM 3M TWIN AXIAL CABLE, SL8800 SERIES 2. PHYSICAL: COLOR: SILVER MARKING: 3M (part number) 30 AWG (signal plating) VW1 (lot code) EXAMPLE: D D 3M SL8801/12-10DA5-00 30 AWG SILVER TW602-1 15.60 EXAMPLE VW1: 3M SL8801/12-1FDG5-00 30 AWG 7.08 SILVER VW1 TW602-1 C 3. REGULATORY INFORMATION: ROHS COMPLIANT. SEE THE REGULATORY INFORMATION APPENDIX 6.52 4.95 (RIA) IN THEROHS COMPLIANC SECTION OF WWW.3MCONNECTORS.COM C FOR COMPLIANCE INFORMATION (RIA E1 & C1 APPLY) 2.58 +.25 1 1.00 UL FILE NUMBER: E42769 -.00 5.18 THE OUTER SURFACE OF THE RIBBON 4. 2 PLACES CABLE HAS A METALLIC APPEARANCE, BUT IS NOT CONDUCTIVE. THERE IS 2.81 C A TRANSLUCENT POLYESTER OUTER LAYER OVER AN ALUMINUM SHIELDING C C LAYER, WHICH GIVES THIS APPEARANCE. THIS CABLE CONSTRUCTION HAS A THIN ALUMINUM LAYER AT EACH EDGE. USER SHOULD EVALUATE ITS USE IN THEIR 0.874 0.038 APPLICATION AND, IF NECESSARY, 0.79 INSULATING TAPE MAY BE APPLIED TO C COVER THE ALUMINUM LAYER, AS USER 4 PLACES DEEMS APPROPRIATE. SIGNAL WIRES: 0.56 FOIL AND INSULATOR STRIPPING 5. 30 AWG SOLID ( 0.254 .0100 ) 3 PLACES BLADE DESIGN DRAWINGS ARE SILVER OR TIN PLATED COPPER AVAILABLE UPON REQUEST. GROUND WIRES: 0.787 .0310 TOOLING REFERENCE NUMBER: NU6D 30 AWG SOLID ( 0.254 .0100 ) POLYOLEFIN INSULATION TIN PLATED COPPER 8 PLACES 6. C DENOTES CRITICAL DIMENSION. 2 PLACES SIDEBAND WIRES: B B 30 AWG SOLID ( 0.254 .0100 ) TIN PLATED COPPER 0.558 .0220 POLYOLEFIN INSULATION 4 PLACES E 79896 AUG 07,2018 LDS MML ADDED CRITICAL DIM SYMBOLS ADDED NOTE 6 1 REVISED TOLERANCE DESIGN REFERENCE NEXT ASSEMBLY REV ECO ISSUE DATE AND DESCRIPTION DRFT CHKD ACCESS DRFT DATE MFG DATE HORIZONTAL FLAME CODES MWL MAR 04,2011 VW1 VERSION VERSION CHKD DATE APPVL DATE RE MAR 04,2011 DIVISION DIVISION CODE C 3M COPYRIGHT 2018 SILVER SL8801/12-10DA5-00 SL8801/12-1FDG5-00 3M Center SIGNAL WIRE This document and the information it contains are 3M property and may not be reproduced or further St. Paul, SCALE TOLERANCES DO NOT distributed without 3M permission, or used or PLATING EXCEPT AS MN 55144 disclosed other than for 3M authorized purposes. TIN SL8801/12-11DA5-00 SL8801/12-1GDG5-00 15 SCALE All rights reserved. NOTED A A 1 DRAWING TITLE INCHES PRODUCT SPEC. PS-0105 PS-0163 .0 SL8801/12-1XDX5-00, .00 .000 IMPEDANCE SPEC. 100 5 OHMS 95 5 OHMS 100 OHM, 30 AWG, 4PR, THIRD ANGLE PROJECTION .0000 MILLIMETERS INTERPRET PER 4SBC ASME Y14.5 - 2009 0 .0 CAGE SIZE DRAWING NO. REV. MAX SURFACE ROUGHNESS .00 0.10 NUMBER ALL SURFACES .000 78-5100-2412-4 E Visit 4 3 2 1 D D Regulatory: For regulatory information about this product, visit 3M.com/regs or contact your 3M representative. Technical Information: The technical information, recommendations and other statements contained in this document are based upon tests or experience that 3M believes are reliable, but the accuracy or completeness of such information is not guaranteed. Product Use: Many factors beyond 3M s control and uniquely within user s control can affect the use and performance of a 3M product in a particular application. Given the variety of factors that can affect the use and performance of a 3M product, user is solely responsible for evaluating the 3M product and determining whether it is fit for a particular purpose and suitable for user s C C method of application. Warranty, Limited Remedy, and Disclaimer: Unless an additional warranty is specifically stated on the applicable 3M product packaging or product literature, 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OR TRADE. If the 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M s option, replacement of the 3M product or refund of the purchase price. Limitation of Liability: Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product, whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted, including warranty, contract, negligence or strict liability. B B 3M Electronics Materials Solutions Division 6801 River Place Blvd. Austin, TX 78726-9000 1-800-225-5373 www.3M.com/interconnect E 79896 AUG 07,2018 LDS MML ADDED CRITICAL DIM SYMBOLS ADDED NOTE 6 1 REVISED TOLERANCE DESIGN REFERENCE NEXT ASSEMBLY REV ECO ISSUE DATE AND DESCRIPTION DRFT CHKD ACCESS DRFT DATE MFG DATE CODES MWL MAR 04,2011 CHKD DATE APPVL DATE RE MAR 04,2011 DIVISION DIVISION CODE C 3M COPYRIGHT 2018 3M Center This document and the information it contains are 3M property and may not be reproduced or further St. Paul, SCALE TOLERANCES DO NOT distributed without 3M permission, or used or EXCEPT AS MN 55144 disclosed other than for 3M authorized purposes. 1 SCALE All rights reserved. NOTED A A 1 DRAWING TITLE INCHES .0 SL8801/12-1XDX5-00, .00 .000 100 OHM, 30 AWG, 4PR, THIRD ANGLE PROJECTION .0000 MILLIMETERS INTERPRET PER 4SBC ASME Y14.5 - 2009 0 .0 CAGE SIZE DRAWING NO. REV. MAX SURFACE ROUGHNESS .00 0.10 NUMBER ALL SURFACES .000 78-5100-2412-4 E 125 MODEL DET. MARKED ONLY ANGLES 1 YES NO SHT 2 OF 2 LISTS 4 3 2 1 78-5100-2412-4 E DRAWING NUMBER REVISION Imaged: Central Standard Time 8/7/2018 -- UTC Offset (hrs) 6