Data Sheet GE TM 12V Austin MicroLynx : SIP Non-Isolated DC-DC Power Modules 10Vdc 14Vdc input 0.75Vdc to 5.5Vdc output 5A Output Current Features RoHS Compliant Compliant to RoHS EU Directive 2011/65/EU (-Z versions) Compliant to RoHS EU Directive 2011/65/EU under exemption 7b (Lead solder exemption). Exemption 7b will expire after June 1, 2016 at which time this product will no longer be RoHS compliant (non-Z versions) Delivers up to 5A output current High efficiency 89% at 3.3V full load (V = 12.0V) IN Small size and low profile: 22.9 mm x 10.2 mm x 6.65 mm (0.9 in x 0.4 in x 0.262 in) Low output ripple and noise Applications High Reliability: Distributed power architectures o Calculated MTBF = 5.6M hours at 25 C Full-load Intermediate bus voltage applications Output voltage programmable from 0.75 Vdc to 5.5Vdc via external resistor Telecommunications equipment Line Regulation: 0.3% (typical) Servers and storage applications Load Regulation: 0.4% (typical) Networking equipment Temperature Regulation: 0.4 % (typical) Enterprise Networks Remote On/Off Latest generation ICs (DSP, FPGA, ASIC) and Microprocessor powered applications Output overcurrent protection (non-latching) Wide operating temperature range (-40C to 85C) UL* 60950-1Recognized, CSA C22.2 No. 60950-1-03 Certified, and VDE 0805:2001-12 (EN60950-1) Licensed ISO** 9001 and ISO 14001 certified manufacturing facilities Description TM Austin MicroLynx 12Vdc SIP (single in-line package) power modules are non-isolated dc-dc converters that can deliver up to 5A of output current with full load efficiency of 89% at 3.3V output. These modules provide precisely regulated output voltage programmable via external resistor from 0.75Vdc to 5.5Vdc over a wide range of input voltage (V = 10 - IN 14V). Their open-frame construction and small footprint enable designers to develop cost- and space-efficient solutions. Standard features include remote On/Off, programmable output voltage and overcurrent protection. * UL is a registered trademark of Underwriters Laboratories, Inc. CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. ** ISO is a registered trademark of the International Organization of Standards September 25, 2015 2015 General Electric Company. All rights reserved. Data Sheet GE TM 12V Austin MicroLynx : SIP Non-Isolated DC-DC Power Modules 10Vdc 14Vdc input 0.75Vdc to 5.5Vdc output 5A Output Current Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Device Symbol Min Max Unit Input Voltage All VIN -0.3 15 Vdc Continuous Operating Ambient Temperature All TA -40 85 C (see Thermal Considerations section) Storage Temperature All Tstg -55 125 C Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Symbol Min Typ Max Unit Operating Input Voltage All VIN 10 12 14 Vdc Maximum Input Current All IIN,max 3.5 Adc (VIN= VIN, min to VIN, max, IO=IO, max ) Input No Load Current V = 0.75 Vdc I 17 mA O,set IN,No load (V = V , Io = 0, module enabled) V = 5.0Vdc I 100 mA IN IN, nom O,set IN,No load Input Stand-by Current All IIN,stand-by 1.2 mA (V = V , module disabled) IN IN, nom 2 2 Inrush Transient All I t 0.4 A s Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 1H source impedance V to V All 30 mAp-p IN, min IN, max, IO= IOmax See Test configuration section) Input Ripple Rejection (120Hz) All 30 dB CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to being part of a complex power architecture. To preserve maximum flexibility, internal fusing is not included, however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fast-acting fuse with a maximum rating of 6 A (see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturers data sheet for further information. September 25, 2015 2015 General Electric Company. All rights reserved. Page 2