IND080 Hornet: Non-Isolated DC-DC Voltage Regulator Modules 12Vdc input 0.8Vdc to 2Vdc output 80W Max Power Vin+ Vout+ VIN VOUT VS+ PGOOD MODULE Applications Cin TRIM Co SEQ RTrim Industrial Equipment SHARE Control Boards ON/OFF SIG GND Test Equipment SYNC GND VS- GND Electrical Features 12V Input voltage with 20% Tolerance Mechanical Features Output voltage programmable from 0.8Vdc to 2Vdc via Small size: 33.02 mm x 13.46 mm x 10.9 mm (1.3 external resistor in x 0.53 in x 0.429 in) Remote On/Off for optional external control Operating range: -40C to 105C ambient Power Good signal for external monitoring Operating shock to 40G per Mil Std. 810G, Fixed switching frequency Method 516.4 Procedure I Output overcurrent protection (non-latching) Operating vibration per Mil Std. 810G, Method Share and Sequence available for advanced loads 514.5 Procedure I Process and Safety Qualified for 1000h High Temperature Operating Bias, 1000h 85RH/85C Temperature, Humidity and Bias, 700 cycle -40 to 125C thermal cycling ANSI/UL* 62368-1 and CAN/CSA C22.2 No. 62368-1 Recognized, DIN VDE 0868-1/A11:2017 (EN62368-1:2014/A11:2017) ISO** 9001 and ISO 14001 certified manufacturing facilities Compliant to RoHS Directive 2011/65/EU and amended Directive (EU) 2015/863 Compliant to REACH Directive (EC) No 1907/2006 Compatible in a Pb-free or SnPb reflow environment. Suitable for aqueous clean. Suitable for conformal coating with dip and vapor deposition. Conformal coating can provide the protection to meet Salt Fog Test per IEC 60068-2-52 (Severity 3) and Mixed Gas Flow test per Telcordia GR-3108 Outdoor Levels. 3 year warranty Output Output Device Code Input Voltage On/Off Logic Comcode Voltage Current (Max.) Negative 1600102901A IND080 9.6 14.4Vdc 0.6 2.0Vdc 40A Thermal Performance Full rated output with natural convection up to 63C at 1.2Vout and up to 60C at 1.8Vout. Thermal curves for 1.2V, and 1.8Vout below. 45 45 40 40 35 35 NC NC 0.5m/s 30 0.5m/s 30 (100LFM) 1m/s (100LFM) 1m/s 25 (200LFM) (200LFM) 25 1.5m/s 20 1.5m/s 1.2Vout 2m/s (300LFM) 20 (400LFM) 15 Current (A) vs. Temp ( C) 2m/s 1.8 Vout 15 (400LFM) 10 Current (A) vs. Temp ( C) 10 5 45 55 65 75 85 95 105 45 55 65 75 85 95 105 May 13, 2021 2017 General Electric Company. All rights reserved. Page 1 Electrical Specifications Parameter Device Symbol Min Typ Max Unit Operating Input Voltage All V 9.6 12 14.4 Vdc IN Input No Load Current V = O,set I 104 mA IN,No load (VIN = 12.0Vdc, IO = 0, module enabled) 2Vdc External Capacitance, Ceramic ESR 1 m All C 6x47 6x47* F O, max 82.8(1.2V), 88.2(1.8V), 91.6(3.3V), Efficiency 12VINDC, TA=25C, I=12A, Vo=1.2 to 5Vdc % 93.9(5V) Switching Frequency All fsw 600 kHz Output Voltage (Over all line, load, and temperature conditions) All VO, set -3.0 +3.0 % VO, set On/Off Logic High (MODULE OFF) Input High Voltage All VIH 2 14.4 Vdc On/ Off Logic Low (MODULE ON) Input Low Voltage All VIL -0.2 0.4 Vdc PGOOD (Power Good) Signal Interface Open Drain, V 5VDC supply Overvoltage threshold for PGOOD ON All 103 108 113 %VO, set Overvoltage threshold for PGOOD OFF All 105 110 115 %VO, set Undervoltage threshold for PGOOD ON All 87 92 97 %V O, set Undervoltage threshold for PGOOD OFF All 85 90 95 %VO, set Pulldown resistance of PGOOD pin All 50 Sink current capability into PGOOD pin All 5 mA Frequency Synchronization (SYNC) All Synchronization Frequency Range All 350 480 kHz High-Level Input Voltage All VIH 2.0 V Low-Level Input Voltage All VIL 0.4 V Input Current, SYNC All ISYNC 100 nA Minimum Pulse Width, SYNC All tSYNC 100 ns Maximum SYNC rise time All tSYNC SH 100 ns *Additional External Capacitance possible using Tunable Loop Characteristic Curves o The following figures provide typical characteristics for the IND080 Hornet at 25 C. 40 6x47uF Ext Cap 8x47uF Ext Cap 30 10x47uF Ext Cap 20 10 0 0.8 1 1.2 1.4 1.6 1.8 2 Output Voltage(Volts) Figure 1. Output Ripple Voltage(20MHz BW) for various output Figure 2. Typical Start-up using Input Voltage (Vin=12V, voltages and external caps 12Vin. Additional Decoupling cap of Vout = Vout, max, Iout = Iout, max) 0.1uF used on input and output side Trim Without an external resistor between Trim and GND pins, the output of the module will be 0.6Vdc. Rtrim for a desired output voltage, should be as per the following table. The formula in the last column helps determine Rtrim for other voltages. Vo (V) 0.9 1.2 1.5 1.8 12 Rtrim = k Rtrim (k) 40 20 13.3 10 (Vo 0.6 ) May 13, 2021 2017 General Electric Company. All rights reserved. Page 2 Ripple (mVp-p)