Data Sheet GE * JRCW016A0R Orca Series DC-DC Converter Power Modules 3675 Vdc Input 28Vdc Output 16Adc Output Features RoHS Compliant Compliant to RoHS Directive 2011/65/EU and amended Directive (EU) 2015/863 (-Z versions) Compliant to REACH Directive (EC) No 1907/2006 3 High power density: 166 W/in Very high efficiency: >93.5% Typ at Full Load Industry standard half-brick pin-out Low output ripple and noise Industry standard, DOSA compliant half-brick footprint 57.7mm x 60.7mm x 12.7mm (2.27 x 2.39 x 0.5) Remote Sense 2:1 input voltage range Single tightly regulated output Constant switching frequency Applications Constant Current Overcurrent limit RF Power Amplifier Latch after short circuit fault shutdown Wireless Networks Over temperature protection auto restart Switching Networks Output voltage adjustment trim, 14.0V to 35.2V dc dc Wide operating case temperature range (-40C to 100C) CE mark meets 2014/35/EU directives ANSI/UL* 62368-1 and CAN/CSA C22.2 No. 62368-1 Recognized, Options DIN VDE 0868-1/A11:2017 (EN62368-1:2014/A11:2017) Output OCP/OVP auto restart ** ISO 9001 and ISO 14001 certified manufacturing facilities Shorter pins Compliant to IPC-9592A, Category 2, Class II Unthreaded heatsink holes Tunable Loop* for transient response optimization Description The JRCW016A0R Orca series of dc-dc converters are a new generation of isolated, very high efficiency DC/DC power modules providing up to up to 16Adc output current at a nominal output voltage of 28Vdc in an industry standard, DOSA compliant half-brick size footprint, which makes it an ideal choice for high voltage and high power applications. Threaded-through holes are provided to allow easy mounting or addition of a heatsink for high-temperature applications. The output is fully isolated from the input, allowing versatile polarity configurations and grounding connections. This module contains an optional new feature, the Tunable Loop, that allows the user to optimize the dynamic response of the converter to match the load with reduced amount of output capacitance, leading to savings on cost and PWB area. * Trademark of General Electric Company UL is a registered trademark of Underwriters Laboratories, Inc. CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. ** ISO is a registered trademark of the International Organization of Standards April 26, 2021 2016 General Electric Company. All rights reserved. Page 1 Data Sheet GE JRCW016A0R Orca Series DC-DC Converter Power Modules 3675 Vdc Input 28.0Vdc Output 16Adc Output Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Device Symbol Min Max Unit Input Voltage Continuous All V -0.3 80 V IN dc Transient, operational (100 ms) All VIN,trans -0.3 100 Vdc Operating Ambient Temperature All Ta -40 85 C Operating Case Temperature All Tc -40 100 C (See Thermal Considerations section, Figure 17) Storage Temperature All Tstg -55 125 C I/O Isolation Voltage (Current trip point=5mA): Input to Case, Input to Output All 1500 V dc Output to Case All 500 V dc Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Symbol Min Typ Max Unit Operating Input Voltage All VIN 36 48 75 Vdc (see Figure 12 for VIN MIN when using trim-up feature) Maximum Input Current (VIN=36V to 75V, IO=IO, max) All IIN,max 14.0 Adc 2 2 Inrush Transient All I t 2 A s Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 12H source impedance VIN=0V to 75V, IO= IOmax All 20 mAp-p see Figure 7) Input Ripple Rejection (120Hz) All 50 dB CAUTION: This power module is not internally fused. An input line fuse must always be used. This power module can be used in a wide variety of applications, ranging from simple standalone operation to being an integrated part of complex power architecture. To preserve maximum flexibility, internal fusing is not included. Always use an input line fuse, to achieve maximum safety and system protection. The safety agencies require a time-delay or fast-acting fuse with a maximum rating of 25 A in the ungrounded input connection (see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturers data sheet for further information. April 26, 2021 2016 General Electric Company. All rights reserved. Page 2