Data Sheet GE TM 12A Digital SlimLynx Open Frame: Non-Isolated DC-DC Power Modules 3Vdc 14.4Vdc input 0.45Vdc to 5.5Vdc output 12A Output Current Features Ultra low height design for very dense power applications. Small size: 20.32 mm x 11.43 mm x 3 mm (Max) (0.8 in x 0.45 in x 0.118 in) Output voltage programmable from 0.6Vdc to 5.5Vdc via external resistor. Digitally adjustable down to 0.45Vdc Wide Input voltage range (3Vdc-14.4Vdc) Wide operating temperature range -40C to 105C . See derating curves RoHS Compliant DOSA approved footprint TM Digital interface through the PMBus protocol TM Tunable Loop to optimize dynamic output voltage Applications response Distributed power architectures Flexible output voltage sequencing EZ-SEQUENCE Power Good signal Intermediate bus voltage applications Remote On/Off Telecommunications equipment Fixed switching frequency with capability of external Servers and storage applications synchronization Networking equipment Output overcurrent protection (non-latching) Industrial equipment Overtemperature protection Vin+ Vout+ Ability to sink and source current VIN VOUT VS+ Compatible in a Pb-free or SnPb reflow environment PGOOD RTUNE UL* 60950-1Recognized, CSA C22.2 No. 60950-1-03 MODULE SEQ Certified, and VDE 0805:2001-12 (EN60950-1) Licensed CTUNE CLK Compliant to RoHS II EU Directive 2011/65/EU Cin TRIM Co DATA ADDR0 SMBALRT Compliant to REACH Directive (EC) No 1907/2006 RTrim ADDR1 Compliant to IPC-9592 (September 2008), Category 2, ON/OFF RADDR1 RADDR0 Class II SIG GND SYNC GND VS- ISO** 9001 and ISO 14001 certified manufacturing GND facilities Description TM The 12A Digital SlimLynx Open Frame power modules are non-isolated dc-dc converters that can deliver up to 12A of output current. These modules operate over a wide range of input voltage (V = 3Vdc-14.4Vdc) and provide a precisely regulated output IN voltage from 0.45Vdc to 5.5Vdc, programmable via an external resistor and PMBus control. Features include a digital interface using the PMBus protocol, remote On/Off, adjustable output voltage, over current and over temperature protection. The PMBus TM interface supports a range of commands to both control and monitor the module. The module also includes the Tunable Loop feature that allows the user to optimize the dynamic response of the converter to match the load with reduced amount of output capacitance leading to savings on cost and PWB area. * UL is a registered trademark of Underwriters Laboratories, Inc. CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. ** ISO is a registered trademark of the International Organization of Standards The PMBus name and logo are registered trademarks of the System Management Interface Forum (SMIF) January 28, 2014 2014 General Electric Corporation. All rights reserved. Data Sheet GE TM 12A Digital SlimLynx Open Frame: Non-Isolated DC-DC Power Modules 3Vdc 14.4Vdc input 0.45Vdc to 5.5Vdc output 12A Output Current Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Device Symbol Min Max Unit Input Voltage All VIN -0.3 15 V Continuous SEQ, SYNC, VS+ All 7 V CLK, DATA, SMBALERT All 3.6 V Operating Ambient Temperature All T -40 105 C A (see Thermal Considerations section) Storage Temperature All Tstg -55 125 C Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Symbol Min Typ Max Unit Operating Input Voltage All VIN 3 14.4 Vdc Maximum Input Current All IIN,max 10A Adc (V =3V to 14V, I =I) IN O O, max VO,set = 0.6 Vdc IIN,No load 50 mA Input No Load Current (VIN = 12Vdc, IO = 0, module enabled) V = 5Vdc I 220 mA O,set IN,No load Input Stand-by Current All I 20 mA IN,stand-by (VIN = 12Vdc, module disabled) 2 2 Inrush Transient All It 1 A s Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 1 H source impedance V =0 to All 50 mAp-p IN 14V I = I See Test Configurations) , O Omax Input Ripple Rejection (120Hz) All -55 dB January 28, 2014 2014 General Electric Corporation. All rights reserved. Page 2