SNC Abeco

FO-SnC Fiber Optic Strip and Cut Instruction Sheet W a r n i n g T h i s t o o l s h o u l d n o t b e u s e d o n l i v e e l e c t r i c a l c i r c u i t s . I t i s n o t p r o t e c t e d a g a i n s t e l e c t r i c a l s h o c k A l w a y s u s e O S H A / A N S I o r o t h e r i n d u s t r y a p p r o v e d e y e p r o t e c t i o n w h e n u s i n g t o o l s . T h i s t o o l i s n o t t o b e u s e d f o r p u r p o s e s o t h e r t h a n i n t e n d e d . R e a d c a r e f u l l y a n d u n d e r s t a n d i n s t r u c t i o n s b e f o r e u s i n g t h i s t o o l . The Miller FO-SnC combines jack et s tripping , fiber s tripping and the trimming of ar amid y arn (K evlar ) all within a single c ompact ALL-IN-ONE tool. Oper ation Loca t e the s tripper t ool side and slide the black t ab f orwar d as shown in Figur e. 1 The fiber s tripper has thr ee s tripping not ches. The lar ges t s tripping not ch at the out er tip of the t ool is used to s trip cable jack ets fr om 1.6- 3.0mm. Close the t ool ar ound the jack et, hold firmly and dr aw the t ool to w ar ds the end of the cable t o s trip off the jack et ma t erial. The middle not ch is used to s trip 900 micr on tight buf f er down t o the 250 micr on buff er coa ting. Fig.1 The smalles t not ch is used to s trip the 250 micr on coa ting down t o the 125 micr on fiber . Fiber Stripping Ensur e tha t all the fiber s tripping not ches ar e clean and clear of an y debris. Debris in a fiber not ch can damag e or br eak the fiber . The tool ma y be cleaned using a cleaner c ont aining 99% isopr opyl alc ohol such as Miller F S400 Bifur ca t ed F oam Tip Swipes. Fiber Stripping 1) Insert the fiber in to the desir ed tool not ch o o t - y e l p i r m o c . s l 2) Hold the fiber squar e to the t ool. Close the t ool squar ely and firmly ar ound the fiber . 3) Dr aw the t ool to w ar ds the end of the fiber e x erting s t eady pr essur e. As fiber buf f er and acrylat es ma y v ary , we r ecommend b y s t arting with sev er al short s trips t o acquir e the desir ed finished s trip leng th. Fig.2 K evlar T rimming - loca t e the t ool Cut ting side and slide the t ab f orwar d as shown in Figur e. 2 K evlar T rimming and cut to the desir ed leng th NO TE: This tool has been specific ally designed f or the cut ting of ar amid K evlar y arn ONL Y . Use an indus try appr ov ed cable g el cleaner or degr easer t o clean r esidue on the cut ting edges aft er use on cables c ont aining w at er blocking ge l. W ARRANTY: RIPLEY warrants its products against defective materials and workmanship for a period of one year from date of shipment from the RIPLEY factory provided the product is utilized in accordance with instructions and specified ratings. 46 Nooks Hill Road, Cromwell, CT 06416 USA ~ Phone: 800-528-8665 ~ Intl: (01) 860-635-2200 81447 rev1 Fax: (01) 860-635-3631 ~ E-mail: info ripley-tools.com ~ Internet: www .ripley-tools.com 01-26-15ff X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Abeco manufacturer: Other Similar products are found below : FO 103-S 010/UNI/AR 06301 721 CFS-2 900 04601/701 46180