S-25C010A/020A/040A 2 SPI SERIAL E PROM www.sii-ic.com Seiko Instruments Inc., 2007-2015 Rev.4.3 00 C 2 The S-25C010A/020A/040A is a SPI serial E PROM which operate at high speed, with low current consumption and the wide range operation. The S-25C010A/020A/040A has the capacity of 1 K-bit, 2 K-bit, 4 K-bit and the organization of 128 words 8- bit, 256 words 8-bit, 512 words 8-bit. Page write and sequential read are available. Features Operating voltage range: Read 1.6 V to 5.5 V Write 1.7 V to 5.5 V Operation frequency: 5.0 MHz (V = 2.5 V to 5.5 V) CC Write time: 4.0 ms max. SPI mode (0, 0) and (1, 1) Page write: 16 bytes / page Sequential read Write protect: Software, Hardware Protect area: 25%, 50%, 100% Monitors write to the memory by a status register Function to prevent malfunction by monitoring clock pulse Write protect function during the low power supply CMOS schmitt input ( CS , SCK, SI, WP , HOLD ) 6 *1 Endurance: 10 cycles / word (Ta = +25C) Data retention: 100 years (Ta = +25C) Memory capacity: S-25C010A 1 K-bit S-25C020A 2 K-bit S-25C040A 4 K-bit Initial delivery state: FFh, BP1 = 0, BP0 = 0 Operation temperature range: Ta = 40C to +85C *2 Lead-free, Sn 100%, halogen-free *1. For each address (Word: 8-bit) *2. Refer to Product Name Structure for details. Packages 8-Pin SOP (JEDEC) 8-Pin TSSOP TMSOP-8 SNT-8A Caution This product is intended to use in general electronic devices such as consumer electronics, office equipment, and communications devices. Before using the product in medical equipment or automobile equipment including car audio, keyless entry and engine control unit, contact to SII is indispensable. 1 Seiko Instruments Inc. 2 SPI SERIAL E PROM S-25C010A/020A/040A Rev.4.3 00 C Pin Configurations 1. 8-Pin SOP (JEDEC) 8-Pin SOP (JEDEC) Top view Table 1 Pin No. Symbol Description *1 1 8 1 CS Chip select input 2 SO Serial data output 2 7 *1 3 Write protect input WP 3 6 4 GND Ground *1 4 5 5 SI Serial data input *1 6 SCK Serial clock input *1 Figure 1 7 HOLD Hold input 8 VCC Power supply S-25C010A0I-J8T1x *1. Do not use it in high impedance. S-25C020A0I-J8T1x S-25C040A0I-J8T1x 2. 8-Pin TSSOP 8-Pin TSSOP Top view Table 2 Pin No. Symbol Description *1 1 8 1 Chip select input CS 2 7 2 SO Serial data output 3 6 *1 4 5 3 Write protect input WP 4 GND Ground *1 Figure 2 5 SI Serial data input *1 6 SCK Serial clock input S-25C010A0I-T8T1x *1 7 Hold input HOLD S-25C020A0I-T8T1x 8 VCC Power supply S-25C040A0I-T8T1x *1. Do not use it in high impedance. Remark 1. Refer to the Package drawings for the details 2. x: G or U 3. Please select products of environmental code = U for Sn 100%, halogen-free products. 2 Seiko Instruments Inc.