R PART NUMBER DATA SHEET ECLIPTEK CORPORATION EH3620ETTS-80.000M (Data Sheet downloaded on May 20, 2017) REGULATORY COMPLIANCE 2011/65 + 173 SVHC 2015/863 ITEM DESCRIPTION Quartz Crystal Clock Oscillators XO (SPXO) LVCMOS (CMOS) 3.3Vdc 4 Pad 3.2mm x 5.0mm Ceramic Surface Mount (SMD) 80.000MHz 20ppm -40C to +85C ELECTRICAL SPECIFICATIONS Nominal Frequency 80.000MHz Frequency Tolerance/Stability 20ppm Maximum (Inclusive of all conditions: Calibration Tolerance at 25C, Frequency Stability over the Operating Temperature Range, Supply Voltage Change, Output Load Change, First Year Aging at 25C, Shock, and Vibration) Aging at 25C 5ppm/year Maximum Operating Temperature Range -40C to +85C Supply Voltage 3.3Vdc 10% Input Current 35mA Maximum (No Load) Output Voltage Logic High (Voh) 2.7Vdc Minimum (IOH = -8mA) Output Voltage Logic Low (Vol) 0.5Vdc Maximum (IOL = +8mA) Rise/Fall Time 4nSec Maximum (Measured at 20% to 80% of waveform) Duty Cycle 50 10(%) (Measured at 50% of waveform) Load Drive Capability 15pF Maximum Output Logic Type CMOS Pin 1 Connection Tri-State (High Impedance) Tri-State Input Voltage (Vih and Vil) 70% of Vdd Minimum to enable output, 20% of Vdd Maximum to disable output, No Connect to enable output. Absolute Clock Jitter 250pSec Maximum, 100pSec Typical One Sigma Clock Period Jitter 50pSec Maximum, 40pSec Typical Start Up Time 10mSec Maximum Storage Temperature Range -55C to +125C ENVIRONMENTAL & MECHANICAL SPECIFICATIONS Fine Leak Test MIL-STD-883, Method 1014, Condition A Gross Leak Test MIL-STD-883, Method 1014, Condition C Mechanical Shock MIL-STD-202, Method 213, Condition C Resistance to Soldering Heat MIL-STD-202, Method 210 Resistance to Solvents MIL-STD-202, Method 215 Solderability MIL-STD-883, Method 2003 Temperature Cycling MIL-STD-883, Method 1010 Vibration MIL-STD-883, Method 2007, Condition A www.ecliptek.com Specification Subject to Change Without Notice Revision F 02/27/2015 Page 1 of 4 Ecliptek Corporation 3545 Cadillac Ave., Costa Mesa, CA 92626 1-800-ECLIPTEK or 714.433.1200R PART NUMBER DATA SHEET ECLIPTEK CORPORATION EH3620ETTS-80.000M MECHANICAL DIMENSIONS (all dimensions in millimeters) PIN CONNECTION 1 Tri-State 2 Ground/Case Ground 3.20 1.30 0.20 1.00 0.20 (x4) 3 Output MAX 4 Supply Voltage 2 3 LINE MARKING 1 E80.000 2.54 5.00 E=Ecliptek Designator 0.15 0.20 2 XXXXX 1 4 XXXXX=Ecliptek Manufacturing Identifier 1.20 0.20 (x4) 1.20 0.20 Suggested Solder Pad Layout All Dimensions in Millimeters 1.20 (X4) 1.40 (X4) Solder Land 1.14 (X4) 1.00 All Tolerances are 0.1 www.ecliptek.com Specification Subject to Change Without Notice Revision F 02/27/2015 Page 2 of 4 Ecliptek Corporation 3545 Cadillac Ave., Costa Mesa, CA 92626 1-800-ECLIPTEK or 714.433.1200 MARKING ORIENTATION