7x5mm LVDS Oscillator O7LS
(former F4700, F4710 Series)
DATASHEET
LVDS Output
Stabilities to 20 PPM
Temperature Ranges as wide as -40C to +85C
Supply Voltages: 2.5V, 3.3V
Specifications
PARAMETERS MAX (unless otherwise noted)
Frequency Range 25.0 ~ 400.0 MHz
Storage Temperature Range (T ) -55 ~ +125C
STG
Supply Voltage (VDD) 2.5V10% 3.3V10%
Input Current (IDD) 63 mA
Standby Current 30 A
Output Symmetry (50% VP-P) 45% ~ 55%
Rise Time (20%~80% VP-P) 0.5 nS
Fall Time (80%~20% VP-P) 0.5 nS
Differential Output Voltage (V ) 0 .2 4 7 V ~ 0.454V
OD
Differential Offset Voltage (VOS) 1 .125V ~ 1 .37 5V
Output Load 100 Ohms Typical
Start-up Time (TS) 10 mS
1
Output Disable Time 200 nS
1
Output Enable Time 10 mS
Aging (per year @ 25C) 3 PPM
Phase Jitter (12kHz~20MHz) 1 pS
Enable/Disable Function
Pin1 Out 1 (pin 4), Out 2 (pin 5)
1
Active
OPEN
Active
1 Level V 70%V
IH DD
High Z
0 Level V 30%VDD
IL
Available Options by Stability & Operating Temp
Frequency
Operating
Frequency Range (MHz)
Stability Temperature (C)
2
100PPM -10 ~ +70 25.0 ~ 400.0
2
25.0 ~ 400.0
100PPM -40 ~ +85
2
25.0 ~ 300.0
100PPM -40 ~ +105
2
25.0 ~ 400.0
50PPM -10 ~ +70
2
-40 ~ +85 25.0 ~ 400.0
50PPM
2
-40 ~ +105 25.0 ~ 300.0
50PPM
2
25.0 ~ 400.0
25PPM -10 ~ +70
3
25.0 ~ 400.0
-40 ~ +85
25PPM
3
25.0 ~ 400.0
20PPM -10 ~ +70
1
An internal pull-up resistor from pin 1 to pin 6 allows active output if pin 1 is left open
2
Inclusive of 25C tolerance, operating temperature range, input voltage change, load change, reflow, one-year aging, shock, and vibration.
3
Inclusive of 25C tolerance, operating temperature range.
Title / Description: O7LS SERIES STANDARD SPECIFICATIONS
Drawing Number: O7LS-DOC-1 Size: A
Part Number: Cage: 61429
Draftsperson: BEC Approved: MAJ Revision Date: 05/05/2020
Copyright 2020 Fox Electronics. All rights reserved.
7x5mm LVDS Oscillator O7LS
(former F4700, F4710 Series)
DATASHEET
Maximum Soldering Temp / Time 260C / 10 Seconds x2
Moisture Sensitivity Level (MSL) 1
Termination Finish Au over Ni
Seal Method Seam
Lead (Pb) Free Yes
ROHS/REACH Compliant Yes
Notes:
*A 0.01F capacitor should be placed between V (Pin 6) and GND (Pin3) to minimize power supply line noise.
DD
*Dimensional drawing is for reference to critical specifications defined by size measurements.
Certain non-critical visual attributes, such as side castellations, reference pin shape, etc. may vary.
Title / Description: O7LS SERIES STANDARD SPECIFICATIONS
Drawing Number: O7LS-DOC-1 Size: A
Part Number: Cage: 61429
Draftsperson: BEC Approved: MAJ Revision Date: 05/05/2020
Copyright 2020 Fox Electronics. All rights reserved.