T0927-21G Access Communications

Product Specification sheet 30G Series Plug-in Switch Mode Power Supply Unit INPUT MINIMUM NORMAL MAXIMUM AC Input Voltage 90V AC 100 240V AC 264V AC AC Input Frequency -3 Hz 50 / 60 Hz +3 Hz AC Input Current 230V AC 0.6A Input Power (T1516-25G) 32.0W Input Power (T1225-21G) 40.0W Peak Inrush Current Limited to 35A Primary current protection An internal fuse on the AC input line is provided. Configuration Wall mount, AU-pin, 2-conductors, <Active, Neutral> Power consumption at no load Input current 35mA Power consumption (no load) 0.7W max OUTPUT MODEL T0927-21G T1255-21G T1516-25G T2412-21G Normal DC Output Voltage +9V +12V +15V +24V Maximum Load Current 2.7A 2.5A 1.6A 1.2A Minimum Load Current 0.05A 0.05A 0.05A 0.05A Rated Output Power 24.0W 30.0W 24.0W 28.8W Over-voltage Protection *** Not Clamped 16.0V 22.5V Not Clamped Over-current Protection Adaptor protected with 200% of rated output. Load Regulation 5% from 10% to 100% of rated load Short-circuit Protection The adaptor shall not be damaged by shorting the DC output to Ground with auto recovery functioning correctly. Ripple and Noise * 100mV Hold-up Time (min) ** 10mS Output over-shoot <7% of nominal voltage value Temperature coefficient Output voltage temperature coefficient 0.05%/C Turn-on Delay (max) 2 Seconds Rise Time Start-up rise time of <20mS to rise to within regulation limits Switching Efficiency 75% minimum at normal input voltage and full load. * Voltage measured P-P at 20MHz and output parallel with 100nF ceramic & 10uF electrolytic capacitors to ground. Temperature at 25C and nominal AC input voltage. ** At nominal AC voltage and full load. *** Maximum voltage (Zener Clamp). Page 1 of 6 www.accesscomms.com.au/specs/adaptor 30Gspec.pdf Copyright 2006 Access Communications Pty Ltd Product Specification sheet 30G Series Plug-in Switch Mode Power Supply Unit MECHANICAL Dimensions 93.0(L) x 47.0(W) x 34.2(D)mm. Weight (T1516-25G) 181g maximum. Weight (T1225-21G) 190g maximum. Input Plug Type Wall type, SAA 2-pin AS/NZS3112:2000 Output Cord Wire: 18AWG/2C, 2000mm. Output Plug (T0927-21G) DC Barrel Plug (with fork & groove) - 11 x 5.5 x 2.1mm Output Plug (T1225 -21G) DC Barrel Plug (with fork & groove) - 11 x 5.5 x 2.1mm Output Plug (T1516-25G) DC Barrel Plug - 9.5 x 5.5 x 2.5mm Output Plug (T2412-21G) DC Barrel Plug (with fork & groove) - 11 x 5.5 x 2.1mm ENVIRONMENTAL Cooling Natural convection. Operating Temperature (T1516-25G) 0C to +30C Operating Temperature (T1225-21G) 0C to +40C Storage Temperature -20C to +80C Operating Humidity 10 ~ 90 % Non-condensing Storage Humidity 10 ~ 90 % Non-condensing SAFETY Dielectric withstanding voltage test (Hi-pot test) 3000V AC 10mA for 1 minute.. input to output Insulation Resistance (T1516-25G) 10M at 500V DC between Input to Output Insulation Resistance (T1225-21G) 50M at 500V DC between Input to Output. Leakage Current 0.25mA maximum at normal AC input voltage and frequency RELIABILITY Mean Time Between The power supply is designed to have a MTBF of 50,000 hours. Failure (MTBF) Page 2 of 6 www.accesscomms.com.au/specs/adaptor 30Gspec.pdf Copyright 2006 Access Communications Pty Ltd