TSOP382.., TSOP384.., TSOP392.., TSOP394.. Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Very low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Improved shielding against EMI Supply voltage: 2.5 V to 5.5 V Improved immunity against ambient light Insensitive to supply voltage ripple and noise 19026 Compliant to RoHS Directive 2002/95/EC and in accordance to WEEE 2002/96/EC MECHANICAL DATA DESCRIPTION Pinning for TSOP382.., TSOP384..: These products are miniaturized receivers for infrared 1 = OUT, 2 = GND, 3 = V S remote control systems. A PIN diode and a preamplifier are Pinning for TSOP392.., TSOP394..: assembled on a lead frame, the epoxy package acts as an IR filter. 1 = OUT, 2 = V , 3 = GND S The demodulated output signal can be directly decoded by a microprocessor. The TSOP382.., TSOP392.. are compatible with all common IR remote control data formats. The TSOP384.., TSOP394.. are optimized to suppress almost all spurious pulses from energy saving fluorescent lamps but will also suppress some data signals. This component has not been qualified according to automotive specifications. PARTS TABLE STANDARD APPLICATIONS VERY NOISY ENVIRONMENTS (AGC2) (AGC4) CARRIER FREQUENCY PINNING 1 = OUT, 2 = GND, 3 = V 1 = OUT, 2 = V , 3 = GND 1 = OUT, 2 = GND, 3 = V 1 = OUT, 2 = V , 3 = GND S S S S 30 kHz TSOP38230 TSOP39230 TSOP38430 TSOP39430 33 kHz TSOP38233 TSOP39233 TSOP38433 TSOP39433 36 kHz TSOP38236 TSOP39236 TSOP38436 TSOP39436 38 kHz TSOP38238 TSOP39238 TSOP38438 TSOP39438 40 kHz TSOP38240 TSOP39240 TSOP38440 TSOP39440 56 kHz TSOP38256 TSOP39256 TSOP38456 TSOP39456 BLOCK DIAGRAM APPLICATION CIRCUIT 16833-13 17170 5 R 1 3 Transmitter IR receiver with V + V S S 30 k TSALxxxx C 1 1 C OUT Band Demo- V Input AGC O pass GND dulator GND 2 R and C are recommended for protection against EOS. 1 1 PIN Control circuit Components should be in the range of 33 < R < 1 k, 1 C > 0.1 F. 1 ** Please see document Vishay Material Category Policy: www.vishay.com/doc 99902 Document Number: 81733 www.vishay.com Rev. 1.5, 04-Feb-11 1 Circuit TSOP382.., TSOP384.., TSOP392.., TSOP394.. IR Receiver Modules for Remote Vishay Semiconductors Control Systems ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V - 0.3 to + 6 V S Supply current I 3mA S Output voltage V - 0.3 to (V + 0.3) V O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T - 25 to + 85 C stg Operating temperature range T - 25 to + 85 C amb Power consumption T 85 C P 10 mW amb tot Soldering temperature t 10 s, 1 mm from case T 260 C sd Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability. ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT E = 0, V = 3.3 V I 0.27 0.35 0.45 mA v S SD Supply current E = 40 klx, sunlight I 0.45 mA v SH Supply voltage V 2.5 5.5 V S E = 0, test signal see fig. 1, v Transmission distance IR diode TSAL6200, d45 m I = 250 mA F 2 I = 0.5 mA, E = 0.7 mW/m , OSL e Output voltage low V 100 mV OSL test signal see fig. 1 Pulse width tolerance: 2 Minimum irradiance t - 5/f < t < t + 6/f , E 0.15 0.35 mW/m pi o po pi o e min. test signal see fig. 1 t - 5/f < t < t + 6/f , pi o po pi o 2 Maximum irradiance E 30 W/m e max. test signal see fig. 1 Angle of half transmission Directivity 45 deg 1/2 distance TYPICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb 1.0 Optical Test Signal E e (IR diode TSAL6200, I = 0.4 A, 30 pulses, f = f , t = 10 ms) Output Pulse Width F 0 0.9 0.8 Input Burst Length 0.7 t 0.6 t * pi 0.5 T 0.4 * t 10/f is recommended for optimal function pi 0 0.3 Output Signal 16110 V O = 950 nm, 0.2 1) Optical Test Signal, Fig.1 7/f < t < 15/f 0 d 0 V OH 2) t - 5/f < t < t + 6/f 0.1 pi 0 po pi 0 0 V OL 2 3 4 5 0.1 1 10 10 10 10 10 2) 1) t t t po d 2 20752 E - Irradiance (mW/m ) e Fig. 1 - Output Active Low Fig. 2 - Pulse Length and Sensitivity in Dark Ambient www.vishay.com Document Number: 81733 2 Rev. 1.5, 04-Feb-11 t - Output Pulse Width (ms) po