PCIe-7300A 32-ch 80 MB/s High-Speed Digital I/O Cards Features x1 lane PCI Express Interface 32-ch 5 V/TTL digital inputs/outputs 20 MHz (80 MB/s) maximum transfer rate 8, 16, or 32-bit transfers 4 auxiliary DI & 4 auxiliary DO Onboard 64 KB FIFO Onboard programmable timer pacer clock Timed digital input sampling controlled by internal timer or external clock Independent trigger signals to start data acquisition and pattern generation Scatter-gather DMA Supports handshaking digital I/O transfer mode Repeated digital pattern generation from FIFO Active terminators Supported Operating System Terminal Boards & Cables Windows 7/10, Linux DIN-100S-01 Terminal Board with One 100-pin SCSI-II Connector and DIN-Rail Mounting (Cables are not included.) Driver and SDK Note: Legacy DIN-502S can be replaced by two DIN-50S-01 and ACL-10252-1 (100-Pin to two 50-Pin Cable, 1 M) LabVIEW, C/C++, Visual Studio.NET, MATLAB ACL-102100-1 100-pin SCSI-II cable (mating with AMP-787082-9), 1 M Software Utility * For more information on matinsg cables, please refer to P3- 48/49. AD-Logger Ordering information PCIe-7300A 80 MB/S High-Speed 32-ch Digital I/O PCIe Card External clock up to 40 MHz Specifications Handshaking Digital I/O Burst handshaking Numbers of channel (Software configurable) Programmable counter 16 DI & 16 DO Base clock: 10 MHz 32 DI 32 DO Timer 0 as digital input pacer Compatibility: 5 V/TTL Timer 1 as digital output pacer Digital logic levels Timer 2: as interrupt source Input high voltage: 2-5.25 V Auxiliary digital I/O Input low voltage: 0-0.8 V Number of channels Output high voltage: 2.7 V minimum Output low voltage: 0.5 V maximum 4-ch digital inputs Input load 4-ch digital outputs Terminator OFF Compatibility: 5 V/TTL - Input high current: 1 mA Data transfers: programmed I/O - Input low current: 20 mA General Specifications Terminator ON I/O connector: One 100-pin SCSI-II female - Termination resistor: 111 - Termination voltage: 2.9 V Operating temperature: 0C to 60C (32F to 140F) - Input high current: 1 mA Storage temperature: -20C to 80C (-4F to 176F) - Input low current: 22.4 mA Relative humidity: 5% to 95%, non-condensing Output driving capacity Power requirements Source current: 8 mA Onboard Onboard Sink current: 48 mA Device Power terminator off terminator on Transfer characteristics +12 V 119 mA typical 287 mA typical PCIe-7300A +3.3 V 499 mA typical 543 mA typical Data transfers: Bus-mastering DMA with Scatter/Gather Dimensions (not including connectors) Data width: 32/16/8 bits (programmable) 168 mm x 112 mm (6.55 x 4.36 ) (PCIe-7300A) Data transfer count 2 M double words (8 MB) for non-chaining mode DMA No limitation for chaining mode (scatter/gather) DMA Max transfer rate DO: 80 MBytes/s, 32-bit output 20 MHz DI: 80 MBytes/s, 32-bit input 20 MHz Trigger ADI TRG for digital inputs, DO TRG for digital outputs Compatibility: 5 V/TTL Trigger types: rising or falling edges Minimum pulse width: 32 ns Clocking mode Internal clock Internal clock sources: 20 MHz, 10 MHz, Timer 0 output (digital input pacer) and Timer 1 output (digital output pacer) www.adlinktech.com All products and company names listed are trademarks or trade names of their respective companies. Updated Nov. 20, 2020. 2020 ADLINK Technology, Inc. All Rights Reserved. All specifications are subject to change without further notice.