T6-DDI ADLINK Technology

Computer-On-Modules Useful time saving tools to expedite your application development Engineering Test Tools The BattMan Smart Battery Management Reference Platform allows BattMan developers to first verify on a system level and then easily implement Smart Battery Management the same type of battery power design into their own carrier board. Reference Platform BattMan supports single battery mode or balanced loading and unloading using two batteries. Contents Smart Battery management module Two Li-ion smart batteries at 14.V, 5200 mAh each 19V notebook type adapter (110/220Vac) USB key with schematics, BOM and manual Ordering Information Model Number Description/Configuration StarterKit-Battman Smart Battery Management Reference Platform for COM Express modules (includes two Smart Batteries, 19V adapter and USB key) The Flat Panel Transfer Board (FPTB) supports prototyping and Flat Panel Transfer Board verification of LVDS and TTL flat panel displays . The module includes an LVDS-to-TTL converter to allow users to implement TTL displays with COM modules that support LVDS only. Onboard PWM circuitry supports backlight control for LVDS and TTL displays. Ordering Information Model Number Description/Configuration FPTB Flat Panel Transfer Board for LVDS-to-TTL signal conversion LVDS cable for FPTB Reference carrier LVDS output to FPTB LVDS input cable (supports Express-BASE, Express-BASE6 and nanoX-BASE) Note: Included in the Starter Kit - nanoX. The ADD2 DVI-D Adapter Card provides DVI-D display output (digital ADD2 DVI-D Adapter Card only) for modules that support SDVO output. This adapter plugs into the PEG x16 connector on Express-BASE, SDVO connector on nanoX-BASE, and DDI connector on Express-BASE6. Ordering Information Model Number Description/Configuration FI-7307(N16D)-F ADD2 DVI-D Adapter The ADLINK PCIe x16-to-two-x8 adapter card can be used with PCIe x16-to-two-x8 Adapter Card modules that support bifurbication on the PEG x16 interface. The card reroutes the PCIe x16 to two x8 and allows testing of two independent PCIe add-on cards with x8/x4/x2/x1 width. Ordering Information Model Number Description/Configuration P16TO28 PCIe x16-to-two-x8 adapter card All ADLINK COM modules include an LPC debug connector. The LPC POST Debug Board LPC POST Debug Board connects to this connector and can provide monitoring of BIOS POST status. The LPC POST Debug Board connects directly to the module and can be used regardless of the carrier board being used. Ordering Information Model Number Description/Configuration LPC DEBUG 2 LPC POST debug board with secondary LPC BIOS The COM-T6T2 Adapter Board allows COM Express Type 6 modules COM-T6T2 Adapter Board to be tested on existing COM Express Type 2 carriers. The adapter COM Express Type 6 to Type 2 Conversion board adds PATA IDE (via a SATA to PATA bridge) and PCI bus (via a PCIe-to-PCI bridge) to the signals on the CD connector. The SDVO port is rerouted to correspond to the Type 2 pin definition. PCIe x16 is not supported. Ordering Information Model Number Description/Configuration COM-T6T2 COM Express Type 6 to Type 2 adapter card (w/ SDVO) The T6-DDI Video Adapter Card provides connector access to COM T6-DDI Video Adapter Card Express Type 6 module Digital Display Interface (DDI) outputs. The COM Express Type 6 DDI to HDMI/DVI/DisplayPort card must be installed on the Express-BASE6 Type 6 carrier board using the second PCIe x16 slot with proprietary pinout. Jumper settings on the card configure output to either HDMI or DisplayPort. DVI can be tested by using a passive dongle connected to a DisplayPort output. Ordering Information Model Number Description/Configuration T6-DDI COM Express Type 6 DDI-to-HDMI/DVI/DisplayPort adapter card (includes DVI dongle)