14962 AIM

RA Cored Wire Solder Rosin Activated Cored Wire Solder Features: - High Activity Level - Fully Activated Flux - Improved Wetting Properties - Good Thermal Transfer - Glycol-Free *Meets QQS-571-E Specification and Applicable IPC-J-STD-004 and -006 Requirements Description: RA is a fully activated, general-purpose wire solder for use in applications where mildly activated fluxes are too weak. RA cored wire is strong enough for excellent tarnish and oxide removal, and will produce bright shiny solder joints. RA wire will leave slight to moderate post process residues that may be left on noncritical applications, but should be removed from any critical applications. RA cored wire meets Mil-Spec cleanliness requirements post-cleaning. IPC flux classification for this material is ROM1. Availability: - RA is standard with a 3.0% flux core for tin-lead (2.0% flux core for lead-free) alloys. - RA is available in Sn/Pb, Sn/Ag/Cu, SN100C alloys. - Other flux percentages, alloys, diameters and spool sizes may be available upon special request. Application: - Solder iron tip temperature should be between 340C-400C (650F-750F) for Sn63, Sn62 and Sn60 alloys, 370C- 425C (700F-800F) for Sn/Ag and Sn/Ag/Cu alloys and 340C-370C (650F-700F) for Sn43/Pb43/Bi14. - Hold the solder iron at a 45 to 60 angle to the work surface. - The solder iron should contact both the component lead and PCB pad surface. - Solder and flux should flow onto both the lead and pad or lead and barrel to promote optimum flux activity to the joint being worked. - If additional flux is needed, the use of AIMs RA301 flux is recommended. Operators should use an applicator capable of dispensing precise amounts of flux to eliminate over-saturation and excessive spread. Cleaning: If post-process cleaning is desired, is easiest if performed within a two to three hour period. Adequate cleaning may be accomplished using a saponifier. AIMTERGE-520A is recommended. A temperature of 35C-65C (100F-150F) is sufficient for removing residues. An in-line or other pressurized spray cleaning system is suggested, but is not required. Handling and Storage: - RA cored wire has a 7 year shelf life when stored < 85F (< 29C). - Store RA in a clean dry area away from moisture and sunlight. - Do not freeze this product. Safety: - Use with adequate ventilation and proper personal protective equipment. - Refer to the accompanying MSDS for any specific emergency information. - Do not dispose of any waste materials in non-approved containers. Canada +1-514-494-2000 USA +1-401-463-5605 Mexico +52-656-630-0032 Europe +44-1737-222-258 Asia-Pacific +86-755-2993-6487 India +91-80-41554753 info aimsolder.com www.aimsolder.com AIM IS ISO9001:2008 & ISO14001:2004 CERTIFIED The information contained herein is based on data considered accurate and is offered at no charge. Product information is based upon the assumption of proper handling and operating conditions. All information pertaining to solder paste is produced with 45-micron powder. Liability is expressly disclaimed for any loss or injury arising out of the use of this information or the use of any materials designated. Please refer to X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Solder category: Click to view products by AIM manufacturer: Other Similar products are found below : 600YSY 701-2758 707-0425 707-1746 707-1748 707-1811 707-1813 707-1831 707-1840 707-1850 707-1852 13-217-3-01 P10695 SN63WRAP3-.022-1-LB 24-6040-0007 DAC-061 599Z 701-2089 707-0285 707-0366 707-0441-26 707-1774 707-1810 24-6337-9727 601Y 24-9574-7619 24-4060-2437 14-6040-0125 04-0595-0000 V5S35 42G 217 V8B45 60G 138 V5B45 42G 138 V3B45 20G 138 XGS20 20G 158 631960 S2626-O-T 8055 5760140 TRWR-204 1152 EC2002M-1 WPT17 WS6016 760-2028 ART.AGT-030 54068 8S005 4900-18G 648107 811008