Click on Series name for product info on aimtec.com Series AM1LT-NZ 1 Watt DC-DC Converter FEATURES: Low Profile SMD Operating Temperature: -40C to +85C 1500 and 3000 VDC I/O Isolation 3000 VDC Isolation regulated modes Pin-out compatible with DCP01 Series RoHS Compliant Short circuit protection Models Single output Output Voltage Output Current Isolation Efficiency Model Input Voltage(V) (V) max(mA) (VDC) (%) AM1LT-0505S-NZ 4.5-5.5 5 200 1500 74 AM1LT-0512S-NZ 4.5-5.5 12 83 1500 77 AM1LT-0515S-NZ 4.5-5.5 15 67 1500 76 AM1LT-1212S-NZ 10.8-13.2 12 83 1500 76 AM1LT-0505SH30-NZ 4.75 -5.25 5 200 3000 70 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Nominal Typical Maximum Units 5 4.5-5.5 & 4.75-5.25 Voltage range VDC 12 10.8-13.2 5 -0.7 9 Absolute Max Input VDC 12 -0.7 - 18 Filter Capacitor Isolation Specifications Parameters Conditions Typical Rated Units Tested I/O voltage 60 Sec, 1mA 1500 & 3000 VDC Resistance 500Vdc 1000 MOhm Capacitor 25 pF Output Specifications Parameters Conditions Typical Maximum Units 1500V Isolation models See tolerance envelope graph Voltage accuracy 3000V Isolation models 3 % Short Circuit protection Continuous Short circuit restart Auto-Recovery For 1500V Isolation models & Vin change of 1% 1.2 Line voltage regulation % of Vin For 3000V Isolation models & Vin change of 5% 0.25 10% to 100% load for 1500V Isolation models 12.8 Load voltage regulation % 10% to 100% load for 3000V Isolation models 1 o Temperature coefficient Nominal input,100% full load 0.03 %/ C Ripple & Noise 20MHz Bandwidth 75 mVp-p Minimum Load Current 10 % of Max NOTE: It is not recommended to have the outputs connected in parallel www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R8.H 1 of 3 North America only Series AM1LT-NZ 1 Watt DC-DC Converter General Specifications Parameters Conditions Typical Maximum Units Switching frequency 100% load 100 KHz o Operating temperature For 3000V Isolation derating above 71C -40 to + 85 C o Storage temperature -55 to +125 C o Maximum case temperature 100 C Cooling Free Air Convection Humidity 95 % RH Case material Epoxy Resin(UL94-V0) Weight 1.4 g Dimensions (L x W x H) 0.77 x 0.42 x 0.20inches19.50 x 10.53 x 5.10 mm o >1,500,000 hours (MIL-HDBK -217F, Ground Benign, t=+25 C) for 1500V Isolation models MTBF o >3,500,000 hours (MIL-HDBK -217F, Ground Benign, t=+25 C) for 3000V Isolation models o Maximum Soldering Temperature 1.5mm from case for 10 seconds 260 C Pin Out Specifications Single Pin 1 +Vin 2 -Vin 5 -Vout 6 +Vout 7 NC 8 NC 14 NC NC: not connected Dimensions Typical Characteristics Front View Tolerance Envelope Graph Side View 7.62 19.50 (0.30) (0.77) Typical Load Line +10% +5% 5.10 4.50 +2.5% (0.20) (0.18) -2.5% 2.54 1.27 -7.5% (0.10) 10.53 0.60 (0.05) (0.42) (0.02) 2.00 1.00 Top View (0.08) (0.04) 14 8 10% 50% 100% Output Current(%) 6.60 10.53 (0.28) (0.42) 1 2 5 6 7 2.54 (0.10) Minimum Load Requirement In order for this module to operate efficiently and reliably a minimum load of no less than 10% of its maximum needs to be maintained at all times during operation. NOTE: this converter should never be operated under no load. If it is required to operate the converter with less than 10% load, it is recommended to install a resistor in parallel with the application load to draw additional current from the converters output to maintain the minimum load condition, or use a converter rated at a lower power. www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R8.H 2 of 3 North America only Output Voltage