Click on Series name for product info on aimtec.com Series AM2LV-NZ 2 Watt DC-DC Converter FEATURES: SMD Package Operating Temperature: -40C To +85C Regulated Single / Dual Output Wide (2:1) Input Range 1500 VDC Isolation MTBF >1,000,000 Hours Continuous Short Circuit Protection RoHS Compliant Models Single output Input Voltage Output Voltage Output Current Isolation Efficiency Model (V) (V) max (mA) (VDC) (%) AM2LV-1203S-NZ 9-18 3.3 500 1500 70 AM2LV-1205S-NZ 9-18 5 400 1500 74 AM2LV-1212S-NZ 9-18 12 167 1500 78 AM2LV-2403S-NZ 18-36 3.3 500 1500 72 AM2LV-2405S-NZ 18-36 5 400 1500 76 AM2LV-2412S-NZ 18-36 12 167 1500 80 Models Dual output Input Voltage Output Voltage Output Current Isolation Efficiency Model (V) (V) max (mA) (VDC) (%) AM2LV-1209D-NZ 9-18 9 111 1500 76 AM2LV-1212D-NZ 9-18 12 83 1500 78 AM2LV-1215D-NZ 9-18 15 67 1500 80 AM2LV-2405D-NZ 18-36 5 200 1500 74 AM2LV-2409D-NZ 18-36 9 111 1500 76 AM2LV-2412D-NZ 18-36 12 83 1500 78 AM2LV-2415D-NZ 18-36 15 67 1500 80 NOTE: Unless otherwise specified, all specifications are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load. Input Specifications Parameters Nominal Typical Maximum Units 12 9-18 Voltage range VDC 24 18-36 12 22 Absolute Maximum Rating VDC 24 40 Peak Input Voltage time 100 ms Isolation Specifications Parameters Conditions Typical Rated Units Tested I/O voltage 60 sec 1500 VDC Resistance At 500 VDC 1000 MOhm Capacitance Input to Output 85 pF Output Specifications Parameters Conditions Typical Maximum Units Voltage accuracy 5 % Short Circuit protection Continuous Short circuit restart Auto-Recovery Line voltage regulation (Single) From Low in to High In 0.5 % Load voltage regulation (Single) From 10% to 100% load 1 % From 10% to 100% load Load voltage regulation (Dual) 5 % Each output loaded within 5% of each other o Temperature coefficient 0.03 %/ C www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R8.G 1 of 4 North America only Series AM2LV-NZ 2 Watt DC-DC Converter Output Specifications (continued) Parameters Conditions Typical Maximum Units Ripple & Noise * 20MHz Bandwidth with 10% load 75 mV p-p Minimum Load Current** 10 % of Max * Test Ripple & Noise by Parallel Cable Method as described in Application Note Ripple and Noise Measurement of Brick & POL DC-DC Converters available on Aimtecs website www.aimtec.com. Converters are designed to operate with a minimum load of 10%. If converter is operated with a load less than 10% the ripple will increase. ** Operation under 10% load will not damage the converter However, not all specifications will be met. General Specifications Parameters Conditions Typical Maximum Units Switching frequency 100% load 300 KHz o Operating temperature -40 to +85 C o Storage temperature -55 to +125 C o Maximum case temperature C o Derating Above 71 2.9 %/ C Cooling Free Air Convection Humidity 95 % RH Case material Plastic (UL94-V0) Weight 5.2 g Dimensions (L x W x H) 0.94 x 0.54 x 0.32 inches 23.86 x 13.70 x 8.20 mm MTBF >1,000,000 hours (MIL-HDBK -217F, Ground Benign, t=+25C) o Maximum Soldering Temperature 1.5mm from case for 10 seconds 260 C Pin Out Specifications Pin Single Dual 1 - Vin - Vin 7 NC NC 8 NC Common 9 +Vout +Vout 10 - Vout -Vout 16 + Vin + Vin NC not connected Dimensions www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R8.G 2 of 4 North America only