Click on Series name for product info on aimtec.com Series AM3LV-NZ 3 Watt DC-DC Converter FEATURES: SMD package Operating temperature: -40C to +85C Regulated Output Wide (2:1) input range 1500VDC isolation MTBF>1,000,000 hours Continuous short circuit protection Models Single output Output Voltage Output Current Isolation Efficiency Model Input Voltage(V) (V) max(mA) (VDC) (%) AM3LV-1205S-NZ 9-18 5 600 1500 75 AM3LV-1212S-NZ 9-18 12 250 1500 77 AM3LV-1215S-NZ 9-18 15 200 1500 79 AM3LV-2405S-NZ 18-36 5 600 1500 76 AM3LV-2412S-NZ 18-36 12 250 1500 81 AM3LV-2415S-NZ 18-36 15 200 1500 80 AM3LV-4805S-NZ 36-75 5 600 1500 77 AM3LV-4812S-NZ 36-75 12 250 1500 80 AM3LV-4815S-NZ 36-75 15 200 1500 80 Models Dual output Input Voltage Output Voltage Output Current Isolation Efficiency Model (V) (V) max (mA) (VDC) (%) AM3LV-1205D-NZ 9-18 5 300 1500 76 AM3LV-1212D-NZ 9-18 12 125 1500 80 AM3LV-1215D-NZ 9-18 15 100 1500 80 AM3LV-2405D-NZ 18-36 5 300 1500 76 AM3LV-2412D-NZ 18-36 12 125 1500 80 AM3LV-2415D-NZ 18-36 15 100 1500 80 NOTE: Unless otherwise specified, all specifications are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load. Input Specifications Parameters Nominal Typical Maximum Units 12 9-18 Voltage range 24 18-36 VDC 48 36-72 12 25 Absolute Maximum Rating 24 50 VDC 48 100 Peak Input Voltage time 100 ms Input Filter Pi () Isolation Specifications Parameters Conditions Typical Rated Units Tested I/O voltage 60 sec 1500 VDC Resistance At 500 Vdc 1000 MOhm Capacitance Input to Output 1000 pF www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R8.C 1 of 4 North America only Series AM3LV-NZ 3 Watt DC-DC Converter Output Specifications Parameters Conditions Typical Maximum Units Voltage accuracy 1 % Short Circuit protection Continuous Short circuit restart Auto-Recovery Line voltage regulation (Single) From Low in to High In 0.2 % Load voltage regulation (Single) From 5% to 100% load 0.2 % From 10% to 100% load Load voltage regulation (Dual) 5 % Unbalanced load Transient Recovery Time 25% Load Step Change 0.5 m sec Transient Response Deviation 25% Load Step Change 2 % o Temperature coefficient 0.03 %/ C Ripple & Noise * 20MHz Bandwidth 100 mVp-p * Converters are designed to operate with a minimum load of 5%. If converter is operated with a load less than 10% the ripple will increase. General Specifications Parameters Conditions Typical Maximum Units Switching frequency 100% load 350 KHz o o Operating temperature -40 to +85 C C o o Temperature Rise Full load, 25 C 25 C o o Storage temperature -55 to +125 C C o Maximum case temperature 100 C Above 71C on dual output Derating See Chart models, others above 85C Cooling Free Air Convection Humidity 95 % RH Case material Epoxy resin (UL94-V0 rated) Weight 5.2 g Dimensions (L x W x H) 0.94 x 0.54 x 0.34inches 23.86 x 13.70 x 8.50 mm MTBF >1,000,000 hours(MIL-HDBK -217F, Ground Benign, t=+25C) o Maximum Soldering Temperature 1.5mm from case for 10 seconds 260 C . Pin Out Specifications Pin Single Dual 1 - Vin - Vin 7 NC NC 8 NC Common 9 +Vout +Vout 10 - Vout -Vout 16 + Vin + Vin NC not connected www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R8.C 2 of 4 North America only