Click on Series name for product info on aimtec.com Series AMEPR15D-AZ up to 1A AC-DC LED Driver FEATURES: AC-DC Constant Current LED Driver Leading or Trailing Edge Triac Input range 90-264VAC/47-440Hz IP20 or IP67 Case High Efficiency up to 82% Active PFC with TRIAC Dimmable Operating temperature -20 to 80C SCP, Over Load Protection Total Harmonic Distortion < 20% 5 Year Limited Warranty Models Single Output No Load Max Output Efficiency Output Output Voltage Output Input Voltage (%) Model Power Range Voltage Current (A) (VAC/Hz) 115 230 (V max.) VAC VAC (W) (V) +Suffix 15 36-50 62 0.3 90-264/47-440 82 82 AMEPR15D-5030AZ +Suffix 15.8 30-48 62 0.35 90-264/47-440 82 82 AMEPR15D-4835AZ +Suffix 18 24-36 52 0.5 90-264/47-440 81 82 AMEPR15D-3650AZ +Suffix 16.8 12-24 34 0.7 90-264/47-440 81 82 AMEPR15D-2470AZ +Suffix 15 8-15 23 1 90-264/47-440 80 79 AMEPR15D-15100AZ Exceeding the maximum output power will permanently damage the converter. Model Nomenclature for Ordering: Add Suffix -UD Universal AC input 90-264VAC, (no TRIAC dimming option), IP20 Add Suffix -UW Universal AC input 90-264VAC, (no TRIAC dimming option), IP67 Add Suffix -110D AC input 90-135VAC, IP20, 115VAC typical value Add Suffix -110W AC input 90-135VAC, IP67, 115VAC typical value Add Suffix -220D AC input 180-264VAC, IP20, 230VAC typical value Add Suffix -220W AC input 180-264VAC, IP67, 230VAC typical value NOTE: Aimtec limited warranty of 5 years is valid based on product operation at datasheet specifications at ambient temperature of 25C, humidity<75%, nominal input voltage (115/230VAC) and at rated output load unless otherwise specified. See Series AMEPR15D-AZ up to 1A AC-DC LED Driver Output Specifications Parameters Conditions Typical Maximum Units Current accuracy 7 % Line regulation LL-HL 10 % Load regulation 0-100% load 7 % Ripple & Noise 3 V p-p Hold-up time 1 ms Minimum load voltage See the models table Ripple and Noise are measured at 20MHz bandwidth by using a 0.1F (M/C) or (C/C) and 47F (E/C) parallel capacitor. Isolation Specifications Parameters Conditions Typical Maximum Units Tested I/O voltage 3sec 3000 VAC Isolation resistance >1000 M General Specifications Parameters Conditions Typical Maximum Units Switching frequency 65 KHz Over load protection 110 % Over voltage protection 110 % Short circuit protection Auto recovery Short circuit restart Over temperature protection >105C o With derating over 55C C Operating temperature -20 to +80 (for IP67 case) o Maximum case temperature 100 C o Storage temperature -40 to +95 C o Temperature coefficient 0.02 % / C Cooling Free air convection Humidity 95 % RH Case material Plastic Wires UL1015 Input 18AWG*10CM / Output 20 AWG*10CM IP20 160 Weight g IP67 200 Dimensions (L X H X W) 133 x 33 x 30mm (5.24 x 1.30 x 1.18 inch) MTBF >400,000 hrs (MIL-HDBK-217F at t=+25C) Environment Approval Test Parameters Conditions Wave form Half sine wave Acceleration amplitude 5gn Shock Bump duration 30 ms Converter operation Before and after test, body mounted (on chassis) Number of bumps 18 (3 in each direction for every axis) Test mode Sweep sine, 10-100Hz, speed 0.05Hz/s Displacement 1 mm Vibration Acceleration 3g, 3 loops 30min one cycle, 3h total, every axis tested Converter operation Before and after test, body mounted (on chassis) www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.S 2 of 5 North America only