Click on Series name for product info on aimtec.com Series AMEPR30D-AZ up to 2A AC-DC LED driver FEATURES: AC-DC Constant current LED Driver Leading or Trailing Edge Triac Input range 90-264VAC/47-440Hz IP67 Case Active PFC with TRIAC dimmable High Efficiency up to 87% Operating temperature -20 to 80C SCP, Over Load Protection Total Harmonic Distortion < 20% 5 Year Limited Warranty Models Single output No Load Max Output Efficiency Output Output Voltage Output Input Voltage (%) Model Power Voltage Range Current (A) (VAC/Hz) 115 230 (V max.) (W) (V) VAC VAC +Suffix AMEPR30D-5070AZ 35 36-50 64 0.7 90-264/47-440 82 85 +Suffix AMEPR30D-4270AZ 29.4 32-42 54 0.7 90-264/47-440 84 84 +Suffix AMEPR30D-3670AZ 25.2 24-36 52 0.7 90-264/47-440 83 84 +Suffix AMEPR30D-36100AZ 36 24-36 52 1 90-264/47-440 83 84 +Suffix AMEPR30D-24125AZ 30 12-24 34 1.25 90-264/47-440 82 84 +Suffix AMEPR30D-24140AZ 33.6 12-24 34 1.4 90-264/47-440 80 83 +Suffix 30 8-15 23 2 90-264/47-440 78 80 AMEPR30D-15200AZ Exceeding the maximum output power will permanently damage the converter. Model Nomenclature for Ordering: Add Suffix -U Universal AC input 90-264VAC, (no TRIAC dimming option) Add Suffix -110 AC input 90-135VAC, 115VAC typical value Add Suffix -220 AC input 180-264VAC, 230VAC typical value NOTE: Aimtec limited warranty of 5 years is valid based on product operation at datasheet specifications at ambient temperature of 25C, humidity<75%, nominal input voltage (115/230VAC) and at rated output load unless otherwise specified. See Series AMEPR30D-AZ up to 2A AC-DC LED driver Ripple & Noise 3 V p-p Hold-up time 1 ms Minimum Load Voltage See the models table Ripple and Noise are measured at 20MHz bandwidth by using a 0.1F (M/C) or (C/C) and 47F (E/C) parallel capacitor. Isolation Specifications Parameters Conditions Typical Maximum Units Tested I/O voltage 60sec 3000 VAC Isolation Resistance >1000 M General Specifications Parameters Conditions Typical Maximum Units Switching frequency 65 KHz Over load protection 110 % Over voltage protection 110 % Short circuit protection Auto recovery Over temperature protection >105C o Operating temperature With derating over 55C -20 to +80 C o Maximum case temperature 100 C o Storage temperature -40 to +95 C o Temperature coefficient 0.02 % / C Cooling Free air convection Humidity 95 % RH Case material Plastic Wires UL1015 Input 18AWG*10CM/ Output 20 AWG * 10CM Weight 200 g Dimensions (L X H X W) 133x33x30mm (5.24 x 1.30 x 1.18 inch) MTBF >400,000 hrs (MIL-HDBK-217F at +25C) Environment Approval Test Parameters Conditions Wave form Half sine wave Acceleration amplitude 5gn Shock Bump duration 30 ms Converter operation Before and after test, body mounted (on chassis) Number of bumps 18 (3 in each direction for every axis) Test mode Sweep sine, 10-100Hz, speed 0.05Hz/s Displacement 1 mm Vibration Acceleration 3g, 3 loops 30min one cycle, 3h total, every axis tested Converter operation Before and after test, body mounted (on chassis) Safety Specifications Parameters Agency approvals CE, FCC EN61347-1, EN61347-2-13, IEC62384, EN55015, EN55024, FCC Part 15 Subpart B, Class B, ANSI C63.4 :2003 Designed to meet UL8750, IEC/EN 60950-1 standards, Harmonic Current Emissions IEC/EN 61000-3-2, Class C Voltage fluctuations and flicker IEC/EN 61000-3-3, (EN60555-3) Electrostatic Discharge Immunity IEC 61000-4-2 Level 3 RF, Electromagnetic Field Immunity IEC 61000-4-3 Level 2 Standards Electrical Fast Transient/Burst Immunity IEC 61000-4-4 Level 2 Surge Immunity IEC 61000-4-5 Level 2 RF, Conducted Disturbance Immunity IEC 61000-4-6 Level 2 Power frequency Magnetic Field Immunity IEC 61000-4-8 Level 2 Voltage dips, Short Interruptions Immunity IEC 61000-4-11 www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.V 2 of 5 North America only