Click on Series name for product info on aimtec.com Series AMEPR8D-AZ up to 0.7A AC-DC LED Driver FEATURES: AC-DC Constant Current LED Driver Class 2 Power Supply Input Range 90-264VAC/47-440Hz Active PFC High Efficiency up to 80% SCP, Over Load Protection Operating Temperature -20 to 85C Leading or Trailing Edge Triac Total Harmonic Distortion < 20% IP67 Case Models Single output Efficiency Output No Load Max Output Output Voltage Output Input Voltage (%) Model Power Current Range Voltage (VAC/Hz) 115 230 (W) (A) (V) (V max.) VAC VAC AMEPR8D-2435AZ 8.4 12-24 34 0.35 90-264/47-440 79 80 AMEPR8D-1840AZ 7.2 9-18 20 0.4 90-264/47-440 77 79 AMEPR8D-1270AZ 8.4 6-12 15 0.7 90-264/47-440 75 78 *Exceeding the maximum output power will permanently damage the converter. NOTE: All specifications in this datasheet are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. AMEPR8D-AZs AC/DC LED drivers have electrical safeguards designed within to protect it from conventional electrical abnormalities with the levels listed in the safety table. Applications for use within rural agricultural, heavy industrial, and other areas or regions which are prone to dirty electrical conditions which would subject any of the above models to excessive voltages surges or spikes, may damage or cause early life failure of product. In this case consideration should be made by the end user to ensure that adequate line or mains surge suppression is installed in front of Aimtec device to ensure the longevity of the products. Failure to identify excessive line surges violations prior to installation may damage sensitive equipment permanently. Input Specifications Parameters Conditions Typical Maximum Units 115 VAC 85 mA Current (full load) 230 VAC 50 mA 115 VAC 10 A Inrush current <2ms (cold start) 230 VAC 5 A Leakage current 230 VAC 0.02 mA 115 VAC (full load) 0.98 Power factor 230 VAC (full load) 0.95 External fuse Recommended slow blow type 1 A Start-up time 100 ms Output Specifications Parameters Conditions Typical Maximum Units Current accuracy 15 % Line regulation (LL-HL) 0.5 % Load regulation min.-max. load 5 % Ripple & Noise* 1.6 V p-p Hold-up time 28 ms Minimum load voltage See the models table Maximum Capacitive Load 200 F *Ripple and Noise are measured at 20MHz bandwidth by using a 0.1F (M/C) or (C/C) and 220F (E/C) parallel capacitor. www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.H 1 of 4 North America only Series AMEPR8D-AZ up to 0.7A AC-DC LED Driver Isolation Specifications Parameters Conditions Typical Maximum Units Tested I/O voltage 3sec 3000 VAC Isolation resistance >1000 M General Specifications Parameters Conditions Typical Maximum Units Switching frequency 66 KHz % Over load protection 110 110 % Over voltage protection Short circuit protection Auto recovery o Operating temperature With derating over 75C Refer to model application C o Storage temperature -40 to +95 C o Maximum case temperature 100 C o Temperature coefficient 0.02 % / C Cooling Free air convection Humidity Non condensing 20~95 % RH Case material Plastic Potting Epoxy (IP67 rated) Wires UL1015 Input 18AWG*10CM / Output 20 AWG*10CM Weight 55 g Dimensions (D X L) 27.4 x 70.3 mm (1.08 x 2.77 inches) MTBF >400,000 hrs (MIL-HDBK-217F at +25C) Environment Approval Test Parameters Conditions Wave form Half sine wave Acceleration amplitude 5gn Shock Bump duration 30ms Converter operation Before and after test, body mounted (on chassis) Number of bumps 18 (3 in each direction for every axis) Test mode Sweep sine, 10-100Hz, speed 0.05Hz/s Displacement 1mm Vibration Acceleration 3g, 3 loops 30min one cycle, 3h total, every axis tested Converter operation Before and after test, body mounted (on chassis) Safety Specifications Parameters Agency approvals cULus, FCC Standards UL8750, UL60950-1, class 2 power supply per UL1310, FCC15, Wire Specifications Wire Parameters Color ACN Blue Input ACL Brown +V Output Red Output -V Output Black www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 052.1e R3.H 2 of 4 North America only