Click on Series name for product info on aimtec.com Series AMLBW-Z Up to 700mA Step Up LED Driver FEATURES: Step UP DC/DC LED driver Operating Temperature 40C to +85C Constant current output Open and Short circuit LED Protection High efficiency up to 94% 2x1 case package Soft Start Drives LED strings of up to 48V PWM/Digital and Analog Voltage dimming Models Single output Maximum Max Ripple & Input Voltage Output Voltage (V) Model Rated Current Capacitive Efficiency (%) Noise (V) Vo-Vin 5V (mA) load (F) (mV p-p) AMLBW-3615Z 9-36 14-48 150 100 90 350 AMLBW-3625Z 9-36 14-48 250 100 92 450 AMLBW-3630Z 9-36 14-48 300 100 92 450 AMLBW-3635Z 9-36 14-48 350 100 92 600 14-45 (Vin:9V-18V) AMLBW-3650Z 9-36 500 47 93 650 23-48 (Vin: 18V-36V) 14-38 (Vin:9V-18V) AMLBW-3660Z 9-36 600 47 93 650 23-48 (Vin: 18V-36V) 14-32 (Vin:9V-18V) AMLBW-3670Z 9-36 700 47 94 700 23-48 (Vin: 18V-36V AMLBW-3690Z 20-30 25-48 900 47 94 400 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Nominal Typical Maximum Units Voltage range 9-36 VDC Filter Capacitor Absolute Maximum Rating 38 VDC Peak Input Voltage time 100 ms DC/DC ON (Leave open if not used) ON Open DC/DC OFF OFF(shutdown) 0V Remote pin drive current <1.5 A VON/OFF 3V (Vin : 9V-32V) 1.3 Quiescent Input Current in Shutdown mode mA (Vin : 32V-36V) 8 Analog and PWM Dimming Control(Leave Absolute Maximum Ratings: 8V open if unused) (DIM) Analog DIM input voltage rang 0.4 to 1.7 V Analog Adjust Output Current 0-100 % DIM Pin Drive Current 0.3Vdim 1.3V <1.5 A PWM Control Voltage Range Limits 1.7Vdim 5.0 V 100Hz-100KHz PWM Recommended Operating Frequency PWM Adjust Output Current 0-100 % Output Specifications Parameters Conditions Typical Maximum Units Current accuracy 5 % Output Voltage range See model table 14-48 VDC Output current Vout-Vin 5V See model table Short Circuit protection Automatic Recovery (Cut-off Output) Over Voltage Protection 52.5 Vdc Under Voltage Protection Cool Start 7.6V Soft Start Time 50 ms o Temperature coefficient 0.03 %/ C Ripple & Noise 20MHz Bandwidth See model table www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.C 1 of 8 North America only Series AMLBW-Z Up to 700mA Step Up LED Driver General Specifications Parameters Conditions Typical Maximum Units Operating frequency Depending on the model 360-380 KHz AMLBW-3615Z -40 to +85 AMLBW-3625Z AMLBW-3630Z -40 to +80 (Vin 9-18V) / -40 to +85 (Vin 18-36V) o Operating temperature C AMLBW-3635Z -40 to +75 (Vin 9-18V) / -40 to +85 (Vin 18-36V) AMLBW-3650Z -40 to +70 (Vin 9-18V) / -40 to +80 (Vin 18-36V) AMLBW-3660Z AMLBW-3670Z -40 to +70 (Vin 9-18V) / -40 to +75 (Vin 18-36V) o Storage temperature -55 to +125 C o Maximum case temperature 100 C o Thermal Impedance Depending on the model +13.7 to +17 C/W Cooling Free air convection Humidity 95 % RH Case material Non-Conductive Black Plastic (UL94-V0 rated) Weight 38 g Dimensions (L x W x H) 2.03 x 1.03 x 0.62 inches 51.50 x 26.10 x 15.80 mm o MTBF > 860 000hrs (MIL-HDBK-217 F at +25 C/Vin=9V,Vout=38V) o Maximum Soldering Temperature 1.5mm from case for 10sec. 260 C NOTES: 1. To prevent burning out the driver, the output voltage must be 5.0VDC higher than the input voltage 2. Do NOT exceed the maximum power ratings on each model 3. With output ripple being rather low, it is recommended not to increase the additional output capacitor so s not to increase the delay while starting up under cool start conditions 4. This series offers protection in case the output is shorted. After the short occurs, thDe input current will be cut off and recovers when the short is removed 5. The reference value of under voltage protection (7.6V) means that under the condition of cool start and full discharge of output, the protection starts when input voltage is lower than 7.6V 6. Note: PWM dimming means PWM signals are converted into mimic analog voltage by internal circuits and then do the dimming. The advantage of this approach is to reduce the EMI Safety Specifications Parameters EMI: Designed to meet EN 55022 Class B Standards Safety : Designed to meet IEC/EN 60950-1 , UL8750, IEC/EN 61347-2-13 Pin Out Specifications Pin Single 1(Red) +Vi + DC Supply 2(White) DIM PWM/Analog Dimming Control 3(Blue) EN Remote ON/OFF 4(Black) -Vi -DC Supply 5(Yellow) +LED LED Anode connection 6(Black) -LED LED Cathode connection www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.C 2 of 8 North America only