AMLDP-1630Z Aimtec

Click on Series name for product info on aimtec.com Series AMLDP-Z Up to 1000mA LED Driver FEATURES: Step Down DC/DC LED driver Operating Temperature range -40C to +85C Constant current output PWM/Digital and Analog Voltage dimming Non-Isolated Remote ON/OFF Control High efficiency up to 93% Built with MLCC capacitors only Models Single output Output Maximum Max Input Voltage Efficiency Model Voltage Rated Current Capacitive Package Type (V) (%) (V) (mA) Load (uF) AMLDP-1630Z 7-16 2-14 300 47 93 DIP8 AMLDP-1635Z 7-16 2-14 350 47 93 DIP8 AMLDP-1650Z 7-16 2-14 500 47 93 DIP8 AMLDP-1660Z 7-16 2-14 600 47 93 DIP8 AMLDP-1670Z 7-16 2-14 700 47 93 DIP8 AMLDP-16100Z 7-16 2-14 1000 47 93 DIP8 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Nominal Typical Maximum Units Voltage range 14 7-16 VDC Filter Capacitor Absolute Maximum Rating 20 VDC Peak Input Voltage time 500 ms DC/DC ON (Leave open if not used) ON Open or 0..2V<Vadj<0.3V DC/DC OFF OFF(shutdown) Vadj <0.15 Maximum Remote pin drive current Vadj = 1.25V 1 mA Quiescent Current in Shutdown Vin = 16V, Vadj 25 uA mode <0.25 On/Off Control (Digital Control) Max PWM Frequency 1KHz Drive with DC Voltage 0.3V < VADJ<1.25V to adjust output current from 1% to 100% Output Specifications Parameters Conditions Typical Maximum Units Current accuracy 5 % Output Voltage range V input = 16 2-14 VDC Output current Vin Vout >1.5V to 3V See model table above Short Circuit protection Regulated at the rated current for each model Output no load Protection Continuous Max load capacitance 47 uF o Temperature coefficient Ta = -40 to +85C 0.03 %/ C Ripple & Noise 20MHz Bandwidth 120 mV p-p General Specifications Parameters Conditions Typical Maximum Units Switching frequency 100% load 90-300 KHz o Operating temperature -40 to +85 C o Storage temperature -40 to +125 C o Maximum case temperature 105 C Thermal Impedance Free air convection +40 Cooling Free air convection Humidity % RH Case material Non-Conductive Black Plastic (UL94-V0 rated) www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.D 1 of 18 North America only Series AMLDP-Z Up to 1000mA LED Driver General Specifications (continued) Parameters Conditions Typical Maximum Units Weight 1.8 g Dimensions (L x W x H) 0.50 x 0.40 x 0.27 inches 12.70 x 10.16 x 6.85 mm o MTBF > 3,300,000 hrs (MIL-HDBK-217 F at +25 C) o Maximum soldering temperature 1.5mm from case for 10sec 260 C NOTES: 1.Reversed polarity at the input power will damage the driver. The input ground must not be connected to the negative output. 2.Leave the pin VADJ opened if not used , grounding VADJ will shut the driver off, connecting VADJ to +Vin will damage the driver. 3.Maximum output open voltage is equal to input voltage Safety Specifications Parameters Agency Approvals CE EN55015: 2007+A2: 2009 EN61547: 2009 IEC 61000-4-2: 2008 IEC 61000-4-3: 2006+A1: 2007+A2: 2010 IEC 61000-4-4: 2004+A1: 2010 Standards IEC 61000-4-5: 2005 IEC 61000-4-6: 2008 IEC 61000-4-8: 2009 IEC 61000-4-11: 2004 NOTE: also designed to meet EN609501 Pin Out Specifications Single Pin 1 + V Input + DC Supply 4 + V Output LED Anode connection 5 - V Output LED Cathode connection 7 Vadj PWM/ON/OFF or not used 8 - V Input - DC Supply Dimensions 0.50 7.62 12.70 (0.02) (0.30) (0.50) 4 1 7.62 10.16 Bottom View (0.30) (0.40) 8 7 5 2.54 (0.10) 6.85 (0.27) NOTES: All dimensions are in millimeters (inch) Pin Diameter: 0.5 0.05 (0.02 0.002) 3.05 Pin Pitch Tolerance: 0.35 ( 0.014) (0.12) Case Tolerance: 0.5 ( 0.02) 0.50 (0.02) 2.54 (0.10) www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832) F 051e R12.D 2 of 18 North America only