CDTTU Altech

Disconnect and Test Terminal Blocks CDTTU CDTTU-SH Disconnect and test terminals are an ideal choice for measuring control and regulatory circuits. The terminals provide a clear functional advantage for devices having utility instruments and associated transformers when it is mandatory to keep the secondary side shorted at any point while tak- ing current measurements. Specially designed socket head Terminal Width 8 mm 16 mm screws act as test/monitoring Height x Length 57 x 63 mm 57 x 63 mm points. Stripping Length 12 mm 12 mm CDTTU + CDTTU-SH - disconnec- tion is achieved by means of a Insulation Material Polyamide 6.6 Polyamide 6.6 slide link operated with a screw driver. Type of Connection 2 screw clamps 4 screw clamps In the CDS6U separate testing Approvals points facilitate insertion of test 60947-7-1 E220514 60947-7-1 E220514 probes. Disconnection is achieved by means of a slide link operated Wire Range 16-8 AWG 1.5-6 sq.mm 16-8 AWG 16-8 AWG 1.5-6 sq.mm 16-8 AWG with a Screw Driver. Voltage Rating 600 V 800 V 600 V 300 V 160 V 300 V In the CDS6U/TS, the insulated Current Rating 41 A 41 A 41 A 25 A 10 A 25 A test point screw system (TPSLS) is integrated. Torque 14 lb-in 1.2 Nm 14 lb-in 14 lb-in 1.2 Nm 14 lb-in CDS6U/FT Terminal Block is a Other Approvals standard feed through Terminal Block. Cat. No. Std. Pk. Cat. No. Std. Pk. In the CDS6U/SC Disconnect & Test Terminal Block, an additional Terminal Block CDTTU 50 CDTTU-SH 50 safety spring is provided under- neath the screw clamp. These End Plate EPCDTTU 50 EPCDTTU 50 Terminal Blocks are preferred for DIN Rail connections that involve safety for ordering information requirements of the Electric refer to pages 90-91 Supply Industry (ESI) standards, British CEGB regulations and End Stop CA702 50 CA702 50 NTPC applications. for ordering information CA802 50 CA802 50 refer to page 92 The SLS2 and SLS4 slide shorting link can be used in combination Internal 2 pole Jumper 3 pole with either the supplied screw or 4 pole the TPSLS Test point screw sys- 5pold tem. 10 pole Slide Shortng Lock out cap LCCDS can be used 2 pole Link 4 pole to lock the center shorting screw, to prevent accidental opening of Insulated Test Gray circuits. Socket Red Yellow Blue Specially designed socket head Black screws act as test/monitoring points in CDTTU and CDTTU-SH. Switchable Link Assembly Important: The disconnecting device is not suitable for interrupt- Lock Out Cap ing load. The supply must be 2 pole CA710/2 100 CA710/2 100 switched off before operating the External 3 pole CA710/3 50 CA710/3 50 Jumper slide link/lever. 4 pole CA710/4 50 CA710/4 50 10 pole CA710/10 20 CA710/10 20 Marking Tags MT8 100 MT8 100 28 Altech Corp. 35 Royal Road Flemington, NJ 08822-6000 Phone (908)806-9400 FAX (908)806-9490 www.altechcorp.comX-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for DIN Rail Terminal Blocks category: Click to view products by Altech manufacturer: Other Similar products are found below : 00110420202 8WA1011-1BH23 8WA1011-1EF20 91.010 9102100000 91.040 9123140000 9123140001 1333564 DP25-GY-ND 1431306 1433306 90.070 91.020 912314 260-301 NR 280-331 280-560 280-564 281-611/281-542 281-673/281-411 281-994 283-317 283-607 284-691 2909798 264-724 264-726 280-530 280-555 280-619 281-610 281-622/281-417 284-317 284-601 2907033 35956 USK 10 102510 1025100000 5520682 591620-2 1-591651-1 8671050000 264-706 280-575 592814-1 592814-3 UMSTBVK 2 5/ 5-STF-5 08 NRA37-12