CDTTU-SH Altech

Disconnect and Test Terminal Blocks CDTTU CDTTU-SH Disconnect and test terminals are an ideal choice for measuring control and regulatory circuits. The terminals provide a clear functional advantage for devices having utility instruments and associated transformers when it is mandatory to keep the secondary side shorted at any point while tak- ing current measurements. Specially designed socket head Terminal Width 8 mm 16 mm screws act as test/monitoring Height x Length 57 x 63 mm 57 x 63 mm points. Stripping Length 12 mm 12 mm CDTTU + CDTTU-SH - disconnec- tion is achieved by means of a Insulation Material Polyamide 6.6 Polyamide 6.6 slide link operated with a screw driver. Type of Connection 2 screw clamps 4 screw clamps In the CDS6U separate testing Approvals points facilitate insertion of test 60947-7-1 E220514 60947-7-1 E220514 probes. Disconnection is achieved by means of a slide link operated Wire Range 16-8 AWG 1.5-6 sq.mm 16-8 AWG 16-8 AWG 1.5-6 sq.mm 16-8 AWG with a Screw Driver. Voltage Rating 600 V 800 V 600 V 300 V 160 V 300 V In the CDS6U/TS, the insulated Current Rating 41 A 41 A 41 A 25 A 10 A 25 A test point screw system (TPSLS) is integrated. Torque 14 lb-in 1.2 Nm 14 lb-in 14 lb-in 1.2 Nm 14 lb-in CDS6U/FT Terminal Block is a Other Approvals standard feed through Terminal Block. Cat. No. Std. Pk. Cat. No. Std. Pk. In the CDS6U/SC Disconnect & Test Terminal Block, an additional Terminal Block CDTTU 50 CDTTU-SH 50 safety spring is provided under- neath the screw clamp. These End Plate EPCDTTU 50 EPCDTTU 50 Terminal Blocks are preferred for DIN Rail connections that involve safety for ordering information requirements of the Electric refer to pages 90-91 Supply Industry (ESI) standards, British CEGB regulations and End Stop CA702 50 CA702 50 NTPC applications. for ordering information CA802 50 CA802 50 refer to page 92 The SLS2 and SLS4 slide shorting link can be used in combination Internal 2 pole Jumper 3 pole with either the supplied screw or 4 pole the TPSLS Test point screw sys- 5pold tem. 10 pole Slide Shortng Lock out cap LCCDS can be used 2 pole Link 4 pole to lock the center shorting screw, to prevent accidental opening of Insulated Test Gray circuits. Socket Red Yellow Blue Specially designed socket head Black screws act as test/monitoring points in CDTTU and CDTTU-SH. Switchable Link Assembly Important: The disconnecting device is not suitable for interrupt- Lock Out Cap ing load. The supply must be 2 pole CA710/2 100 CA710/2 100 switched off before operating the External 3 pole CA710/3 50 CA710/3 50 Jumper slide link/lever. 4 pole CA710/4 50 CA710/4 50 10 pole CA710/10 20 CA710/10 20 Marking Tags MT8 100 MT8 100 28 Altech Corp. 35 Royal Road Flemington, NJ 08822-6000 Phone (908)806-9400 FAX (908)806-9490 www.altechcorp.comX-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for DIN Rail Terminal Blocks category: Click to view products by Altech manufacturer: Other Similar products are found below : 1045932 00110420202 00110430402 5724.2/L 592808-3 CTS25U/BL CTS2.5U-N/Y 90.080 91.010 91.040 DP25-GY-ND 15288 90.070 90.202 90.905 91.001 91.020 91.201 91.340 2713793 280-331 283-317 283-607 2909044 2909798 29-2052 SRT2-OD08CL-1 CDL4U(E)MOV 2757801 2794660 284-317 2890975 2907033 3048496 CTS2.5U-N/O 5542152 5602077 0709880 5520682 5607102 EPUSC SRT2-OD16P 2901288 591620-2 1-591651-1 NRA37-1/2 592814-1 592814-3 SRT2-ID16P NRA37-12