CSFL4U(L)/24 Altech

* CSFL4U CSFL4U(L) FUSE BLOCKS Certain electrical and control systems require protection by fuses. CSFL4U and CSFL6U have a specially designed space for cartridge type glass fuse and accept 5 x 20 or 5 x 25 mm fuses. CAFL4U accepts 1/4 x 1-1/4 in. fuses. The fuse can be engaged or disengaged by the movement of the carrier. Terminal Width 8 mm 8 mm Altech fuse terminals are also Height x Length 43 x 58 mm 43 x 58 mm available with light indication - Stripping Length 9.5 mm 9.5 mm CSFL4U(L). A specially designed built-in circuit gives light Insulation Material Polyamide 6.6 Polyamide 6.6 indication in the event of fuse blow out. Thus, fault in a circuit Type of Connection 2 screw clamps 2 screw clamps can be easily located. Fusion Voltage 24V AC/DC, 48V AC/DC, 110V AC/DC, 220V AC However, an application of such terminals must take into Type of Fuse Used 5x20, 5x25 mm 5x20, 5x25 mm consideration residual current Approvals flow. C US CUS Wire Range 22-10 AWG 0.5-4 sq.mm 22-10 AWG 22-10 AWG 0.5-4 sq.mm 22-10 AWG DDFL4U - Double Level Fuse Terminal with fuse link on the Voltage Rating 600 V 750 V 600 V 600 V 750 V 600 V top level has a separate feed through terminal at the lower Current Rating 6.3 A 6.3 A 8 A 6.3 A 6.3 A 8 A level. This eliminates use of an Torque 7 lb-in 0.5 Nm 7 lb-in 7 lb-in 0.5 Nm 7 lb-in additional feed through terminal. Cat. No. Std. Pk. Cat. No. Std. Pk. Terminal Block CSFL4U 100 CSFL4U(L)* 50 In DDFL4U(E), specially designed built in circuit gives End Plate EPCSFL4U 50 EPCSFL4U 50 light indication in the event of a Isolation Partition PPCSFL4U 50 PPCSFL4U 50 fuse blow out at the top level. The terminal provides separate DIN Rail feed through connection for ordering information possibility at the lower level. refer to page 62 DDFL4U(LR): This is a modified End Stop CA702 50 CA702 50 version of DDFL4U(E) terminal for ordering information CA802 50 CA802 50 where in two equipotential refer to page 63 connection points are available 2 pole External CA711/2 100 CA711/2 100 on both ends of the terminal. 3 pole Jumper CA711/3 100 CA711/3 100 4 pole CA711/4 50 CA711/4 50 10 pole CA711/10 25 CA711/10 25 CAFL4U(L) is equipped with a LED for blown fuse indication. Marking Tags (MT Type) MT8 100 MT8 100 CAFL4U(N) is equipped with a (MT Type on Lever) MT2 100 MT2 100 neon bulb for same application. CB1038 accepts 10 x 38mm fuse. Fuses are sold separately by Altech, see page 34 for details. * Add required voltage to part number as a suffix. i.e. CSFL4U(L)/24 for 24V AC/DC. 30 Altech Corp. 35 Royal Road Flemington, NJ 08822-6000 Phone (908)806-9400 FAX (908)806-9490 www.altechcorp.comX-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for DIN Rail Terminal Blocks category: Click to view products by Altech manufacturer: Other Similar products are found below : 00110420202 8WA1011-1BH23 8WA1011-1EF20 91.010 9102100000 91.040 9123140000 9123140001 1333564 DP25-GY-ND 1431306 1433306 90.070 91.020 912314 260-301 NR 280-331 280-560 280-564 281-611/281-542 281-673/281-411 281-994 283-317 283-607 284-691 2909798 264-724 264-726 280-530 280-555 280-619 281-610 281-622/281-417 284-317 284-601 2907033 35956 USK 10 102510 1025100000 5520682 591620-2 1-591651-1 8671050000 264-706 280-575 592814-1 592814-3 UMSTBVK 2 5/ 5-STF-5 08 NRA37-12