Assembly Assembly Instructions-C25 Amphenol BNC CLAMP CONNECTORS nut washer* gasket clamp bushing female contact jack body male contact plug body * Not supplied on all items For use on RG-62, 71, 122, 178, 180, 196, 210 Stripping Dims, Amphenol Connector Cable Inches (Millimeters) Number Type RG-/U ac 6775 BNC Plug 8, 9, 11, 213, 214 .490(12.4) .200(5.1) 6775-75 75 BNC Plug 11 .490(12.4) .200(5.1) 8525 BNC Angle Plug 58, 141, 142, 400 .343(8.7) .187(4.7) 8575 BNC Angle Plug 59, 62, 140, 210 .297(7.5) .094(2.4) 9350 BNC Plug 6 .405(10.3) .094(2.4) 15875 BNC Plug 178, 196 .156(3.96) .078(1.98) 16300 BNC Plug 180 .250(6.4) .094(2.4) 33275 BNC Angle Plug 174, 179, 187, 188, 316 .540(13.7) .156(3.96) 69475 BNC Plug 174, 179, 187, 188, 316 .281(7.1) .172(4.4) 84975 BNC Plug 122 .281(7.1) .172(4.4) 86350 BNC Bulkh. Jack 174, 179, 187, 188, 316 .265(6.73) .156(3.96) 86425 BNC Panel Jack 174, 179, 187, 188, 316 .313(7.95) .203(5.15) 86850 BNC Bulkh. Jack 178, 196 .266(6.75) .109(2.76) 31-2 BNC Plug 58, 141, 142, 400 .312(7.9) .094(2.4) 31-2-RFX BNC Plug 58, 141, 142A .315(8.0) .118(3.0) 31-15 BNC Jack 59, 62, 71, 140, 210 .297(7.54) .109(2.75) 31-202 BNC Plug 55, 58, 141, 142, 223, 400 .274(6.95) .094(2.4) 31-204 BNC Angle Plug 55, 58, 141, 142, 223, 400 .297(7.54) .109(2.8) Step 1 31-206 BNC Bulkhead Jack 58, 141, 142, 400 .297(7.5) .109(2.8) 31-207 BNC Bulkhead Jack 59, 62, 71, 140, 210 .297(7.54) .109(2.75) 31-212 BNC Plug 59, 62, 71, 140, 210, 302 .250(6.4) .094(2.4) 31-212-1005 BNC Plug 59 (20GA CC) .250(6.4) .094(2.4) a 31-850 BNC Angle Plug 59, 62, 71, 140, 210 .375(9.52) .125(3.17) Step 2 31-3202 BNC Plug 55, 58, 141, 142, 223, 400 .250(6.4) .094(2.4) 31-3301 BNC Plug 58, 141, 142, 223 .250(6.4) .094(2.4) 31-3302 BNC Plug 59, 62, 71, 140, 210 .250(6.4) .094(2.4) c Step 1 Place nut, washer (when supplied) and gasket over cable Step 3 a and strip jacket to dimension shown in table above. Step 2 Comb out braid and fold out. Trim insulation off center c conductor to dimension shown in table above. For RG-62, 71 and 210/U cable, trim an additional .032 (0.8mm) of Step 4 insulation off center conductor and add bushing. Tin center conductor. Step 3 Pull braid wires forward and taper toward center conductor. Step 5 Place clamp over braid and push back against cable jacket. Step 4 Fold back braid wires as shown, trim to proper length approximately .125 (3.2mm) long and form over clamp as shown. Braid wire should not extend beyond step of For angle plugs only: (except 31-204) Solder center braid clamp. Solder contact to center conductor, sliding conductor to preassembled contact. Assemble cap and bushing first (when supplied) over center conductor. lightly punch center of cap for retention in body, or solder in place. Step 5 Insert cable and parts into connector body. Make sure sharp edge of clamp seats properly in gasket. Tighten nut to approximately 15 inch pounds. Amphenol Corporation Tel: 800-627-7100 www.amphenolrf.com 299X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for RF Connectors / Coaxial Connectors category: Click to view products by Amphenol manufacturer: Other Similar products are found below : 8915-1511-000 89674-0827 6001-7071-019 6002-7051-003 6002-7551-202 6059674-1 619550-1 630059-000 M39030/3-01N M3933/25- 36N 6500-7071-046 6769 CX050L2AQ 7002-1542-011 7004-1512-000 7009-1511-004 7010-1511-000 7029-1511-060 7101-1541-010 7101-1571-002 7105-1521-002 7145-1521-002 7203-1571-003 7209-1511-011 7210-1511-015 7210-1511-019 73137-5015 73216-2241 7325-1512-000 73404-2300 7405-1521-005 7405-1521-802 7406-1521-005 8527 8547 FS11V 8808-1511-001 9049-9513-000 9074-9513- 000 9101-9573-002 910A205F 9130-9573-002 PL11SC-026 PL375-33 PL40-5 PL71-9 PL74C-221 PL75MC-217 PL803-7 980-8666-005