Assembly Assembly Instructions-C32 Amphenol BNC CRIMP TERMINATION FOR TYPE 2 75 CONNECTORS outer ferrule bushing male contact plug body assembly female contact jack body assembly for use on RG-62, 71, 210 cable only Hex Crimp Data Stripping Dimensions, inches (mm) Amphenol Connector Cable Number Type RG-/U Cavity for Cavity for Die Set for CTL Series abc Contact Outer Ferrule Tool 227-944* Tool No. 31-71000-RFX 75 BNC Plug 6 .068(1.7) .324(8.2) 227-1221-32 CTL-2 .593(15.1) .250(6.4) .156(4.0) 31-71008 75 BNC Plug 59, 62 .068(1.7) .255(6.5) 227-1221-13 CTL-1 .593(15.1) .250(6.4) .156(4.0) 31-71008-RFX 75 BNC Plug 59, 62 .068(1.7) .255(6.5) 227-1221-13 CTL-1 .630(16.0) .303(7.7) .156(4.0) 31-71008-1RFX 75 BNC Plug 59 (20GA CC) .068(1.7) .255(6.5) 227-1221-13 CTL-1 .630(16.0) .303(7.7) .156(4.0) 31-71008-1000 75 BNC Plug 59, 62 (20GA CC) .068(1.7) .255(6.5) 227-1221-13 CTL-1 .593(15.1) .250(6.4) .156(4.0) 31-71008-2000 75 BNC Plug Plenum -59, B89269 .068(1.7) .255(6.5) 227-1221-13 CTL-1 .593(15.1) .250(6.4) .156(4.0) 31-71010 75 BNC Angle Plug 59, 62 .068(1.7) .255(6.5) 227-1221-13 CTL-1 .578(14.7) .328(8.3) .125(3.2) 31-71010-RFX 75 BNC Plug 59 .068(1.7) .255(6.5) 227-1221-13 CTL-1 .677(17.2) .350(9.0) .156(4.0) 75 BNC Plug 62 .068(1.7) .255(6.5) 227-1221-13 CTL-1 .677(17.2) .350(9.0) .197(5.0) 31-71011 75 BNC Bulkh. Jack 59, 62 .068(1.7) .255(6.5) 227-1221-13 CTL-1 .593(15.1) .250(6.4) .156(4.0) 31-71011-RFX 75 BNC Bulkh. Jack 59, 62 .068(1.7) .255(6.5) 227-1221-13 CTL-1 .689(17.5) .362(9.2) .157(4.0) 31-71013 75 BNC Plug 179, 187 .068(1.7) .178(4.5) 227-1221-9 CTL-2 .539(15.1) .250(6.4) .156(4.0) 31-71013-RFX 75 BNC Plug 179, 187 .068(1.7) .178(4.5) 227-1221-9 CTL-2 .590(15.0) .323(8.2) .118(3.0) 31-71013-1000 75 BNC Plug Dbl. Br. RG-179 .068(1.7) .178(4.5) 227-1221-9 CTL-2 .593(15.1) .250(6.4) .156(4.0) 31-71014-RFX 75 BNC Jack 179, 187 .068(1.7) .178(4.5) 227-1221-9 CTL-2 .571(14.5) .303(7.7) .157(4.0) 31-71016 75 BNC Bulkh. Jack 179, 187 .068(1.7) .178(4.5) 227-1221-9 CTL-2 .593(15.1) .250(6.4) .156(4.0) 31-71016-RFX 75 BNC Bulkh. Jack 179, 187 .068(1.7) .178(4.5) 227-1221-9 CTL-2 .630(16.0) .362(9.2) .157(4.0) 31-71032 75 BNC Plug B8281, 88281 .068(1.7) .324(8.2) 227-1221-32 CTL-2 .593(15.1) .250(6.4) .156(4.0) 31-71033 75 BNC Plug B8218 .068(1.7) .178(4.5) 227-1221-9 CTL-2 .593(15.1) .250(6.4) .156(4.0) 31-71034 75 BNC Plug Belden 89292 .100(2.5) .429(10.9) 227-1221-25 CTL-3 .593(16.7) .250(6.4) .156(4.0) 31-71035 75 BNC Plug PL-59 (20GA CC) .068(1.7) .255(6.5) 227-1221-13 CTL-1 .593(15.1) .250(6.4) .156(4.0) 31-71064 75 BNC Plug Belden 9248, Pl-6 .068(1.7) .324(8.2) 227-1221-32 CTL-2 .593(15.1) .250(6.4) .156(4.0) 31-71065 75 BNC Plug Belden 9290 .068(1.7) .324(8.2) 227-1221-32 CTL-2 .593(15.1) .250(6.4) .156(4.0) 31-71066 75 BNC Plug Quad Shield 59 .068(1.7) .263(6.7) 227-1221-15 .593(15.1) .250(6.4) .156(4.0) a Step 1 Step 1 Strip cable jacket, braid, and dielectric to dimensions in table above. for RG-62,71,210/U cable, trim an b additional .039 (1.0mm) of insulation off center conductor c and add bushing All cuts are to be sharp and square. Important: Do not nick braid, dielectric, and center conductor. Slide outer ferrule onto cable as shown. For RG-174, 179, 187, 188, 316/U cables only, slit jacket back .100 (2.5mm) as shown. Before attaching center contact TFE sleeve (not shown) over cable Step 2 Flare slightly end of cable braid as shown to facilitate dielectric and under braid. For 31-71016, before attaching center contact. insertion of inner ferrule. Important: Do not comb out braid. Slide metal spacer/TFE sleeve (not shown) over cable dielectric and under Place contact on cable center conductor so that it butts braid. The center contact should butt against the dielectric against cable dielectric. Crimp contact in place using and TFE sleeve. Die Set Cavity indicated in table above. When using RG-62, 71, 210, install bushing over center conductor before Step 2 installing contact. contact must butt against cable dielectric Step 3 Install cable assembly into body assembly so that inner ferrule portion slides under braid. Push cable assembly forward until contact snaps into place in insulator. Slide outer ferrule over braid and up against connector body. Step 3 cable dielectric must butt insulator Crimp outer ferrule using Die Set Cavity specified in table above. outer ferrule should butt here * for pneumatic crimp tool 227-60, use die sets indicated in this column Amphenol Corporation Tel: 800-627-7100 www.amphenolrf.com 307X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for RF Connectors / Coaxial Connectors category: Click to view products by Amphenol manufacturer: Other Similar products are found below : 8915-1511-000 89674-0827 6001-7071-019 6002-7051-003 6002-7551-202 6059674-1 619550-1 630059-000 M39030/3-01N M3933/25- 36N 6500-7071-046 6769 CX050L2AQ 7002-1542-011 7004-1512-000 7009-1511-004 7010-1511-000 7029-1511-060 7101-1541-010 7101-1571-002 7105-1521-002 7145-1521-002 7203-1571-003 7209-1511-011 7210-1511-015 7210-1511-019 73137-5015 73216-2241 7325-1512-000 73404-2300 7405-1521-005 7405-1521-802 7406-1521-005 8527 8547 FS11V 8808-1511-001 9049-9513-000 9074-9513- 000 9101-9573-002 910A205F 9130-9573-002 PL11SC-026 PL375-33 PL40-5 PL71-9 PL74C-221 PL75MC-217 PL803-7 980-8666-005