TYPE NUMBER PRODUCT SPECIFICATION GS-12-400 TITLE PAGE REVISION 1 of 6 A AUTHORIZED BY DATE EYE OF NEEDLE PRESS FIT QUICKIE HEADERS M. BARRIOS Sep. 21, 2006 CLASSIFICATION UNRESTRICTED 1.0 SCOPE. 1.1 Content. This specification covers the performance requirements for EON Press Fit Quickie family of compliant, press-fit daughter board post headers. 1.2 Qualification. When tests are performed on the subject product line, the procedures specified in the applicable specifications must be used. All inspections shall be performed using the applicable inspection plans and product drawings. 2.0 APPLICABLE DOCUMENTS 2.1 Specifications. (a) General requirements from test specification. (b) Engineering drawings (c) Process drawings 2.2 Military Standards. (a) MIL-STD-105: Sampling procedure and tables for inspection by attributes. (b) MIL-STD-1344: Test methods from electrical connectors (c) MIL-STD-202: 2.3 Commercial Standards. (a) UL94-V0 3.0 REQUIREMENTS. 3.1 Design and construction. Connectors shall be of the design, construction, and physical dimensions specified on the applicable product drawing. 3.2 Materials. A. Contacts. Copper Alloy, nickel plate all-over or duplex plate of gold, GXT, Tin or Tin-Lead as required by the product drawing. B. Thermoplastic, UL94-V-0 3.3 Performance and Test Description Header assemblies shall be designed to meet the electrical, mechanical, and environmental performance requirements specified in Section 3.4. 3.4 Test Requirements and Procedure Summary. Form E-3334 GS-01-001 Rev E PDM: Rev:A Released .STATUS: Printed: Nov 28, 2010TYPE NUMBER PRODUCT SPECIFICATION GS-12-400 TITLE PAGE REVISION 2 of 6 A AUTHORIZED BY DATE EYE OF NEEDLE PRESS FIT QUICKIE HEADERS M. BARRIOS Sep. 21, 2006 CLASSIFICATION UNRESTRICTED TEST DESCRIPTION REQUIREMENT PROCEDURE Examination of Meets requirements of product Visual, dimensional and functional per QAP product. drawing. Contact to plated 1.0 Milliohms max. init. Test as shown in Figure 1 through hole 4.0 Milliohms max. final resistance Insulation Resistance 5000 Mgohms min. init. Method 3003 of MIL-STD-1344 1000 Mgohms min. final Dielectric No arcover or insulation breakdown or Method 3001 condition 1 of MIL-STD-1344 test Withstanding current leakage greater than 1 voltage 1000 VRMS, 60 cycles per second Voltage (DWV) Milliamp. duration 60 seconds Bend Strength No damage to wire-wrap pin Tested on a circuit board-connector assembly in accordance with method 211 MIL-STD-202 test method C: load of one (1) pound and a maximum bend of 30 , each side of the center line. Torque Strength 1) No damage to wire-wrap terminals Tested to method 211, MIL-STD202 test 2) Meets the final contact to plated condition E with 2 ounce inches of torque through hole resistance Pin to board Three (3) pound min. Pull or push individual pin at a rate of 0.1 inches Retention per minute and measure force required to move pin Pin to housing Three (3) pound min. Pull or push individual pin at a rate of 0.1 inches Retention per minute and measure force required to move pin Pin Stability No visible motion of the board interface Pins assembled to a PCB shall experience a motion of 30 magnitude in any radial direction at either end of the pin Thermal Shock 1) No evidence of crazing, Test to method 1003 of MIL-STD-1344. For cracking or other damage connectors to be used in higher that 85 C to the assembly environment, test to MIL-STD-202 Method 107 Condition. Humidity 1) Meets the insulation resistance final Test to method 1002 of MIL-STD-1344 Type 1, min value. test condition B (96 HOURS AT 40 C and 95% 2) Meets the final contact to plated RH) through hole resistance. Form E-3334 GS-01-001 Rev E PDM: Rev:A Released .STATUS: Printed: Nov 28, 2010