10125595-S01LF Amphenol

NUMBER TYPE PRODUCT SPECIFICATION GS-12-1179 TITLE PAGE REVISION 1 of 11 6 AUTHORIZED BY DATE Barklip R/A Connector Terris Liu 12 May 15 CLASSIFICATION PRELIMINARY 1.0 Objective This specification defines the performance, test, quality and reliability requirements of the Barklip Connector product. 2.0 Scope This specification is applicable to the termination characteristics of the Barklip connector which provides a means of bringing high current levels up to 150A from Bus Bar conductors to printed circuit boards or 170A from Bus Bar to Bus Bar. 3.0 Ratings 3.1 Operating Voltage Rating = 480 VDC (The voltage rating is also dependant on the application) 3.2 Operating Current Rating = 170 Amperes Max. o o 3.3 Operating Temperature Range = -40 C to +105 C 4.0 Applicable Documents 4.1 FCI Specifications 4.1.1 Application Specification: GS-20-0396 4.2 Industry or Trade Association Standards 4.2.1 Telcordia GR-1217 4.3 National or International Standards 4.3.1 Flammability: UL-94V-0 4.3.2 EIA 364: Electrical Connector/Socket Test Procedures Including Environmental Classifications. 4.3.3 IEC 60512: Connectors for Electronic Equipment Tests and Measurement 4.3.4 IEC 60068: Basic environmental testing procedures. 4.4 Safety Agency Approvals 4.4.1 CSA std. C22.2 No. 182.3-M1987 4.4.2 UL-1977 5.0 Requirements 5.1 Qualification Connectors furnished under this specification shall be capable of meeting the qualification test requirements specified herein. Copyright FCI. Form E-3701 Revision C GS-01-029 For information only. This is a preliminary customer document that is subject to change without notice.NUMBER TYPE PRODUCT SPECIFICATION GS-12-1179 TITLE PAGE REVISION 2 of 11 6 AUTHORIZED BY DATE Barklip R/A Connector Terris Liu 12 May 15 CLASSIFICATION PRELIMINARY 5.2 Material The material for each component shall be as specified herein or equivalent. Power Contacts High Conductivity Copper alloy Clip Stainless steel Housing Thermoplastic, UL 94V-0 5.3 Finish The finish for applicable components shall be as specified herein or equivalent. Contact area: See customer drawing 5.4 Design and Construction Connectors shall be of the design, construction, and physical dimensions specified on the applicable product drawing. There shall be no cracks, burrs, or other physical defects that may impair performance. 5.5 Connectors Mating Part (Bus Bar) Recommended material: Copper, solid blade Material Thickness: 3.00.1 mm Common stock width: 20.0 mm minimum Smallest nominal pitch at contacting area: Solder type: 25 mm Screw-mount type: 30mm Pitch tolerance at connector area: 1.0 mm (pitch tolerance includes twist and flatness) Surface roughness in contact area: Ra 1.6 m maximum Plating in contact area: 3 m min Silver over 1.27 m min Nickel Mating edges: 0.5 mm minimum, rounded or chamfered 6.0 Electrical Characteristics 6.1 Contact Resistance, Low Level (LLCR) The low level contact resistance shall not exceed 0.2 milliohms initially. The low level contact resistance shall also not exceed 0.2 milliohms after any treatment and/or environmental exposure. Measurements shall be in accordance with EIA 364-23 The following details shall apply: a. Test Voltage - 20 mV DC Max. open circuit. b. Test Current - 100 mA DC Max. Copyright FCI. Form E-3701 Revision C GS-01-029 For information only. This is a preliminary customer document that is subject to change without notice.