Assembly Instructions-C26 Amphenol BNC 3-PIECE CRIMP PLUGS outer ferrule bushing male contact plug body assembly used with RG-62, 71, 210 cable only Hex Crimp Data Stripping Dimensions, inches (mm) Amphenol Connector Cable Number Type RG-/U Cavity for Cavity for Die Set for CTL Series ab c Contact Outer Ferrule Tool 227-944* Tool Number Belden 82907, 88240 36650-1003 BNC Plug .068(1.7) .178(4.5) 227-1221-9 CTL-2 .593(15.1) .250(6.4) .156(4.0) 89907, Plenum 58 36650-3RFX BNC Plug Plenum 58 .068(1.7) .213(5.4) 227-1221-11 CTL-1 .630(16.0) .319(8.1) .157(4.0) 36875 BNC Plug 55, 142, 223, 400 .068(1.7) .213(5.4) 227-1221-11 CTL-1 .593(15.1) .250(6.4) .156(4.0) 68175-1003 BNC Plug Belden 9259 .068(1.7) .255(6.5) 227-1221-13 CTL-1 .593(15.1) .250(6.4) .156(4.0) 68175-1005 BNC Plug 59 (20AG CC) .068(1.7) .255(6.5) 227-1221-13 CTL-1 .593(15.1) .250(6.4) .156(4.0) Belden 1560A, 82259, 68175-1011 BNC Plug .068(1.7) .255(6.5) 227-1221-13 CTL-1 .593(15.1) .250(6.4) .156(4.0) 89259, Plenum 59, 62 68175-11RFX BNC Plug Plenum 59, 62 .068(1.7) .255(6.5) 227-1221-13 CTL-1 .630(16.0) .303(7.7) .157(4.0) 68175-5RFX BNC Plug 59 (20GA CC) .068(1.7) .255(6.5) 227-1221-13 CTL-1 .630(16.0) .303(7.7) .157(4.0) 31-242 BNC Plug 179, 187 .068(1.7) .178(4.5) 227-1221-9 CTL-2 .593(15.1) .250(6.4) .156(4.0) 31-242-RFX BNC Plug 179, 187 .068(1.7) .178(4.5) 227-1221-9 CTL-2 .590(15.0) .323(8.2) .118(3.0) 31-315 BNC Plug 174, 188, 316 .068(1.7) .178(4.5) 227-1221-9 CTL-2 .593(15.1) .250(6.4) .156(4.0) 31-315-RFX BNC Plug 174, 188, 316 .068(1.7) .178(4.5) 227-1221-9 CTL-2 .654(16.6) .323(8.2) .118(3.0) 31-315-1005 BNC Plug Dbl. Br. 316 .068(1.7) .178(4.5) 227-1221-9 CTL-2 .593(15.1) .250(6.4) .156(4.0) 31-320 BNC Plug 58, 141 .068(1.7) .213(5.4) 227-1221-11 CTL-1 .593(15.1) .250(6.4) .156(4.0) 31-320-RFX BNC Plug 58A, 141, 142A .068(1.7) .213(5.4) 227-1221-11 CTL-1 .630(16.0) .303(7.7) .156(4.0) 31-320-1006 BNC Plug Belden 9907, 89907 .068(1.7) .213(5.4) 227-1221-11 CTL-1 .593(15.1) .250(6.4) .156(4.0) 31-321 BNC Plug 59, 62 .068(1.7) .255(6.5) 227-1221-13 CTL-1 .593(15.1) .250(6.4) .156(4.0) 31-321-RFX BNC Plug 59, 62 .068(1.7) .255(6.5) 227-1221-13 CTL-1 .630(16.0) .303(7.7) .156(4.0) 31-321-1000 BNC Plug Belden 8281, 88281 .068(1.7) .324(8.2) 227-1221-32 CTL-2 .593(15.1) .250(6.4) .156(4.0) 31-321-10RFX BNC Plug Belden 8281 .068(1.7) .324(8.2) 227-1221-32 CTL-2 .630(16.0) .303(7.7) .156(4.0) 31-325 BNC Plug Belden 8218 .068(1.7) .178(4.5) 227-1221-9 CTL-2 .593(15.1) .250(6.4) .156(4.0) 31-326 BNC Plug 55, 142, 223 .068(1.7) .213(5.4) 227-1221-11 CTL-1 .593(15.1) .250(6.4) .156(4.0) 31-326-RFX BNC Plug 55, 142, 223, 400 .068(1.7) .213(5.4) 227-1221-11 CTL-1 .593(15.1) .250(6.4) .156(4.0) 31-4320 BNC Plug 58, 141 .068(1.7) .213(5.4) 227-1221-11 CTL-1 .593(15.1) .250(6.4) .156(4.0) 31-4321 BNC Plug 59, 62 .068(1.7) .255(6.5) 227-1221-13 CTL-1 .593(15.1) .250(6.4) .156(4.0) 31-4411 BNC Plug Belden 8213 .100(2.5) .429(10.9) 227-1221-25 CTL-3 .650(16.5) .250(6.4) .156(4.0) 31-4427 BNC Plug 142, 400 .068(1.7) .213(5.4) 227-1221-11 CTL-1 .593(15.1) .250(6.4) .156(4.0) 31-5558-RFX BNC Plug 6 Type (.314OD) .068(1.7) .324(8.2) 227-1221-32 CTL-2 .630(16.0) .303(7.7) .156(4.0) 31-5800 BNC Plug 58, 141, PL-58 .068(1.7) .213(5.4) 227-1221-11 CTL-1 .593(15.1) .250(6.4) .156(4.0) 59, 62, 59 (20GA CC), 31-5900 BNC Plug .068(1.7) .255(6.5) 227-1221-13 CTL-1 .593(15.1) .250(6.4) .156(4.0) Plenum -59, 62 cable dielectric must butt insulator a Step 1 Step 2 Step 3 b outer ferrule should butt here c contact must butt against cable dielectric crimp here Step 1 Strip cable jacket, braid, and dielec- Step 2 Flare slightly end of cable braid as Step 3 Install cable assembly into body tric to dimensions in table above. for RG- shown to facilitate insertion of inner ferrule. assembly so that inner ferrule portion slides 62,71,210/U cable, trim an additional Important: Do not comb out braid . under braid. Push cable assembly forward .039 (1.0mm) of insulation off center conduc- Place contact on cable center conductor so until contact snaps into place in insulator. tor and add bushing All cuts are to be sharp that it butts against cable dielectric. Crimp Slide outer ferrule over braid and up against and square. contact in place using Die Set Cavity indicat- connector body. Crimp outer ferrule using Important: Do not nick braid, dielectric, and ed in table above. When using RG-62, 71, Die Set Cavity specified in table above. center conductor. Slide outer ferrule onto 210 cable, install bushing over center con- cable as shown. ductor before installing contact. For RG-174, 179, 187, 188, 316/U cables only, slit jacket back .100 (2.5mm) as shown. Before attaching center contact, slide metal spacer/TFE sleeve (not shown) over cable dielectric and under braid. The center contact should butt against the dielectric and TFE sleeve. * for pneumatic crimp tool 227-60, use die sets indicated in this column. Amphenol Corporation Tel: 800-627-7100 www.amphenolrf.com 300X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for RF Connectors / Coaxial Connectors category: Click to view products by Amphenol manufacturer: Other Similar products are found below : 8915-1511-000 89674-0827 6001-7071-019 6002-7051-003 6002-7551-202 6059674-1 619550-1 630059-000 M39030/3-01N M3933/25- 36N 6500-7071-046 6769 CX050L2AQ 7002-1542-011 7004-1512-000 7009-1511-004 7010-1511-000 7029-1511-060 7101-1541-010 7101-1571-002 7105-1521-002 7145-1521-002 7203-1571-003 7209-1511-011 7210-1511-015 7210-1511-019 73137-5015 73216-2241 7325-1512-000 73404-2300 7405-1521-005 7405-1521-802 7406-1521-005 8527 8547 FS11V 8808-1511-001 9049-9513-000 9074-9513- 000 9101-9573-002 910A205F 9130-9573-002 PL11SC-026 PL375-33 PL40-5 PL71-9 PL74C-221 PL75MC-217 PL803-7 980-8666-005