NUMBER TYPE PRODUCT SPECIFICATION BUS-12-064 TITLE PAGE REVISION 1 of 13 F BergPin AUTHORIZED BY DATE H. T. BREWBAKER 04 SEP 08 CLASSIFICATION UNRESTRICTED 1.0 OBJECTIVE This specification defines the performance, test, quality and reliability requirements of the BergPin 0.64mm/0.025 inch square pin product. 2.0 SCOPE This specification covers the BergPin 0.64mm/0.025 inch square pin for use in single or double-sided printed wiring boards. 3.0 GENERAL 3.1 Index This document is composed of the following sections: Paragraph Title Page 1.0 OBJECTIVE 1 2.0 SCOPE 1 3.0 GENERAL 1 3.1 Index 1 3.2 Type 1 3.3 Classification 2 3.4 Banned/Restricted Substances 2 4.0 APPLICABLE DOCUMENTS 2 5.0 REQUIREMENTS 3 5.1 Qualification 3 5.2 Material 3 5.3 Finish 3 5.4 Design and Construction 3 5.5 Electrical Characteristics 4 5.6 Mechanical Characteristics 5 5.7 Environmental Characteristics 6 6.0 QUALITY ASSURANCE PROVISION 8 7.0 PACKAGING AND MARKING 11 8.0 GENERAL INFORMATION 12 3.2 Type The BergPin shall be available in one of the following types, as limited by the appropriate product drawing. Type Plating I. 0,76u/30u gold II. 1,27u/50u gold III. 0,38u/15u gold IV. 3,05u/120u tin-lead V. 0,76u/30u GXT VI. 0,38u/15u GXT VII. 2,54u/100u tin Copyright FCI Form E-3334 GS-01-001 Rev F PDM: Rev:F Released .STATUS: Printed: Nov 28, 2010NUMBER TYPE PRODUCT SPECIFICATION BUS-12-064 TITLE PAGE REVISION 2 of 13 F BergPin AUTHORIZED BY DATE H. T. BREWBAKER 04 SEP 08 CLASSIFICATION UNRESTRICTED 3.3 Classification. BergPin shall be classified as follows: Class I: Reeled BergPin suitable for automatic or semiautomatic application. Class II Loose-piece BergPin suitable for handtool application. Unless otherwise specified herein all requirements are applicable to both classes of BergPin 3.4 Banned/Restricted Substances All product where the part number ends in LF meet the European Union directives and other country regulations as described in GS-22-008. The part numbers that do not end in LF meet all regulations except for Pb in SnPb plating, if available. Tin plated LF product has 100% tin plating in the interface and has not been tested for whisker growth in all interconnect environments. 4.0 APPLICABLE DOCUMENTS 4.1 Issues of Documents . The following documents, of the issue in effect on the date of the latest revision of this specification, shall form a part of this specification to the extent specified herein. SPECIFICATIONS FEDERAL QQ-N-290 Nickel Plating (Electrodeposited) QQ-W-343 Wire Electrical and Nonelectrical, copper, (Uninsulated) QQ-B-613 Brass, Leaded and Nonleaded QQ-B-750 Bronze, Phosphor: Bar, Plate. Rod, Sheet, Strip, Flat Wire, and Structural and Special- Shaped Sections. MILITARY MIL-F-14256 Flux,Soldering. Liquid (Rosin Base), Activated. MIL-P-13949 Plastic sheet, Laminated, Metal-Clad (for printed wiring) General Specification for MIL-G-45204 Gold Plating, Electrodeposited MIL-P-55110 Printed Wiring Boards MIL-P-81728 Plating, Tin-Lead (Electrodeposited) MIL-P-45209 PALLADIUM Plating, (Electrodeposited) MIL-STD-105 Sampling Procedures and Tables for Inspection by Attributes MIL-STD-202 Test Methods for Electrical and Electronic MIL-STD-275 Printed Wiring for Electronic Equipment MIL-STD-1130 Connections, Electrical Solderless Wrapped MIL-STD-1344 Test Methods for Electrical Connectors MIL-STD-45662 Calibration Systems Requirements 4.2 Other Publications The following documents from a part of this specification to the extent specified herein: American Society for Testing and Materials (ASTM) ASTM B-159-Phosphor Bronze Wire Copyright FCI Form E-3334 GS-01-001 Rev F PDM: Rev:F Released .STATUS: Printed: Nov 28, 2010