NUMBER TYPE
PRODUCT SPECIFICATION
BUS-12-064
TITLE PAGE REVISION
1 of 13 F
BergPin
AUTHORIZED BY DATE
H. T. BREWBAKER 04 SEP 08
CLASSIFICATION
UNRESTRICTED
1.0 OBJECTIVE
This specification defines the performance, test, quality and reliability requirements of the BergPin
0.64mm/0.025 inch square pin product.
2.0 SCOPE
This specification covers the BergPin 0.64mm/0.025 inch square pin for use in single or double-sided
printed wiring boards.
3.0 GENERAL
3.1 Index This document is composed of the following sections:
Paragraph Title Page
1.0 OBJECTIVE 1
2.0 SCOPE 1
3.0 GENERAL 1
3.1 Index 1
3.2 Type 1
3.3 Classification 2
3.4 Banned/Restricted Substances 2
4.0 APPLICABLE DOCUMENTS 2
5.0 REQUIREMENTS 3
5.1 Qualification 3
5.2 Material 3
5.3 Finish 3
5.4 Design and Construction 3
5.5 Electrical Characteristics 4
5.6 Mechanical Characteristics 5
5.7 Environmental Characteristics 6
6.0 QUALITY ASSURANCE PROVISION 8
7.0 PACKAGING AND MARKING 11
8.0 GENERAL INFORMATION 12
3.2 Type The BergPin shall be available in one of the following types, as limited by the appropriate
product drawing.
Type Plating
I. 0,76u/30u gold
II. 1,27u/50u gold
III. 0,38u/15u gold
IV. 3,05u/120u tin-lead
V. 0,76u/30u GXT
VI. 0,38u/15u GXT
VII. 2,54u/100u tin
Copyright FCI
Form E-3334 GS-01-001
Rev F
PDM: Rev:F Released .STATUS: Printed: Nov 28, 2010NUMBER TYPE
PRODUCT SPECIFICATION
BUS-12-064
TITLE PAGE REVISION
2 of 13 F
BergPin
AUTHORIZED BY DATE
H. T. BREWBAKER 04 SEP 08
CLASSIFICATION
UNRESTRICTED
3.3 Classification. BergPin shall be classified as follows:
Class I: Reeled BergPin suitable for automatic or semiautomatic application.
Class II Loose-piece BergPin suitable for handtool application.
Unless otherwise specified herein all requirements are applicable to both classes of BergPin
3.4 Banned/Restricted Substances All product where the part number ends in LF meet the
European Union directives and other country regulations as described in GS-22-008. The part
numbers that do not end in LF meet all regulations except for Pb in SnPb plating, if available. Tin
plated LF product has 100% tin plating in the interface and has not been tested for whisker growth
in all interconnect environments.
4.0 APPLICABLE DOCUMENTS
4.1 Issues of Documents . The following documents, of the issue in effect on the date of the latest
revision of this specification, shall form a part of this specification to the extent specified herein.
SPECIFICATIONS
FEDERAL
QQ-N-290 Nickel Plating (Electrodeposited)
QQ-W-343 Wire Electrical and Nonelectrical, copper, (Uninsulated)
QQ-B-613 Brass, Leaded and Nonleaded
QQ-B-750 Bronze, Phosphor: Bar, Plate. Rod, Sheet, Strip, Flat Wire, and Structural and Special-
Shaped Sections.
MILITARY
MIL-F-14256 Flux,Soldering. Liquid (Rosin Base), Activated.
MIL-P-13949 Plastic sheet, Laminated, Metal-Clad (for printed wiring) General Specification for
MIL-G-45204 Gold Plating, Electrodeposited
MIL-P-55110 Printed Wiring Boards
MIL-P-81728 Plating, Tin-Lead (Electrodeposited)
MIL-P-45209 PALLADIUM Plating, (Electrodeposited)
MIL-STD-105 Sampling Procedures and Tables for Inspection by Attributes
MIL-STD-202 Test Methods for Electrical and Electronic
MIL-STD-275 Printed Wiring for Electronic Equipment
MIL-STD-1130 Connections, Electrical Solderless Wrapped
MIL-STD-1344 Test Methods for Electrical Connectors
MIL-STD-45662 Calibration Systems Requirements
4.2 Other Publications The following documents from a part of this specification to the extent specified
herein:
American Society for Testing and Materials (ASTM) ASTM B-159-Phosphor Bronze Wire
Copyright FCI
Form E-3334 GS-01-001
Rev F
PDM: Rev:F Released .STATUS: Printed: Nov 28, 2010