SCALE 6.000 NOTES: THIRD ANGLE PROJ. REVISIONS 1. MATERIALS AND FINISHES (PLATING THICKNESS IN MICROINCHES): REV DESCRIPTION DATE ECO APPR BODY & COUPLING NUT - BeCu, GOLD PLATING (50 MIN THICK) -- OFFICIAL ENG. RELEASE TO MFG. ------ ------ BUSHING, BRAID CLAMP & CLAMP NUT - BRASS, GOLD PLATING (50 MIN THICK) FRONT & REAR INSULATOR - PTFE W REDRAWN IN PROE & ADDED COD 9/20/13 49679 KR 0.328 GASKETS - SILICONE RUBBER Y STAMP ON COD WAS M39012/55-400 10/3/14 50162 CPM RETAINING RING - BeCu CONTACT - BeCu, GOLD PLATING (50 MIN THICK) 0.203 BRAID & DIELECTRIC 2. ELECTRICAL: A. IMPEDANCE: 50 OHM 3. MECHANICAL: A. TEMPERATURE RANGE: -65 C TO +165 C 4. PACKAGING: A. QUANTITY: SINGLE PACK B. MARKING: BAG TO BE MARKED RECOMMENDED CABLE AMPHENOL, 901-128-11, AND DATE COD STRIPPING DIMENSIONS 5. SHOWS CABLE ENTRY DIMENSIONS 6. ASSEMBLY INSTRUCTIONS A. CUT JACKET TO DIMENSION SHOWN. B. COMB OUT BRAID AND FOLD OUT. C. PULL BRAID WIRES FORWARD AND TAPER TOWARD CENTER CONDUCTOR. PLACE CLAMP SCALE 2.500 NUT ASSEMBLY OVER BRAID AND PUSH BACK AGAINST CABLE JACKET. FOLD BACK BRAID WIRES, TRIM AS NECESSARY SO THAT WIRES DO NOT TOUCH SHOULDER OF GASKET. D. SCREW TRIM TOOL 901-G ONTO CLAMP NUT ASSEMBLY. TIGHTEN NUT LIGHTLY. MIL-C-39012 INSPECTION DO NOT DAMAGE GASKET. USING RAZOR BLADE, REMOVE EXPOSED DIELECTRIC. CUT MUST BE SQUARE. DO NOT NICK CENTER CONDUCTOR. E. REMOVE DIELECTRIC TRIM TOOL AND CLEAN ALL SURFACES THOROUGHLY. ASSEMBLE BUSHING ASSEMBLY AND SOLDER CENTER CONTACT TO CABLE. F. THREAD CONNECTOR ASSEMBLY ONTO PREPARED CABLE ASSEMBLY. TIGHTEN TO 20-25 IN.-LBS TORQUE. 0.032 0.114 0.064 5/16 HEX REF 0.405 REF. 0.553 REF. 0.552 REF 0.330 REF CONTACT INTERFACE PER MIL-STD-348 SMA SERIES GASKET BUSHING ASSEMBLY 5/16 0.340 REF ACROSS FLAT CLAMP NUT ASSEMBLY CONNECTOR ASSEMBLY 0.016 MINSTAMP 74868 M39012/55-4007 YYW 3 SAFETY WIRE HOLES (4 DIGIT DATE CODE YEAR & WEEK) THIS CONNECTOR COVERED BY U.S PATENT 3,676,573 & 3,054,981 UNLESS OTHERWISE SPECIFIED, DIMENSIO NS ARE IN INCHES AND TOLERANCES ARE: MATERIAL DATE TITLE DRAWN 2 PLACE DECIMAL 3 PLACE DECIMAL ANGLES 09-Aug-13 KARTHIK R SMA CLAMP TYPE PLUG WITH .015 (0,381 mm) .005 (0,127 mm) 1 Amphenol RF SEE NOTES NOTICE - These drawings, specifications, or other data (1) are, and remain the CAPTIVE CONTACT FOR RG-174/U, ENGINEER DATE property of Amphenol corp. (2) must be returned upon request and (3) are www.amphenolrf.com JAH 24-Jul-70 188/U & 316/U CABLES confidential and not to be disclosed to any person other than those to whom they are given by Amphenol Corp. the furnishing of these drawings, specifications, or REFERENCE APPROVED DATE other data by Amphenol Corp., or to any other person to anyone for any purpose is DRAWING NO.901-128-11 EPA 302202-51 not to be regarded by implication or otherwise in any manner licensing, granting K. CAPOZZI 9/20/13 SCALE: 5.0:1.0 SHEET 2 OF 2 DOR 308033-51 rights to permitting such holder or any other person to manufacture, use or sell any ITEM NO.901-128-11 MIL-C-39012/55-4007 product, process or design, patented or otherwise, that may in any way be related to DWG SIZE CAD FILE REV or disclosed by said drawings, specifications, or other data. PART NO.901-128-11 FINISH B Y