BACC47GN1 Amphenol

Quadrax Contacts, MIL-DTL-38999, Series III Amphenol Aerospace General Description Amphenol Quadrax Contacts -Offer several 38999 advantages for high data transfer rates, low power consumption and III excellent EMI compatibility: HD Four strategically spaced inner contacts form two 100 or 150 Dualok Ohm matched impedance differential pairs II Outer contact has rugged wall section for durability I Available in size 8 crimp termination style Also available in size 8 with PC tails (see page 233) SJT Requires modification of MIL-DTL-38999 connector to Accessories accommodate keyed contacts TYPICAL QUADRAX Aquacon SOCKET CONTACT has socket outer contact Herm/Seal with a socket inner contact (4) CENTER BRAID JACKET CONDUCTORS PCB HIg H TYPICAL QUADRAX PIN CONTACT SPeeD has pin outer contact with a pin INSULATION Fiber inner contact Optics Cable Illustration - Quadrax Contact Quadrax Contacts are gold plated, Contacts crimp termination Connectors Cables Finish of mating contact parts: supplied with 0.000050 min. gold over nickel on mating parts. Consult Amphenol for availability of other finishes. Quadrax Size 8 Contact Performance: Bandwidth: Up to 1.25 GHz Data Rate: Exceeding 2.5 Gbps. Quadrax Pin with 8P8C RJ45 Jack Quadrax Pin Size 8 and MIL-DTL-38999 Voltage Rating: 500 Vrms max. Series III Connector sea level Dielectric Withstanding Voltage: 1000 VAC rms between all inner contacts sea level, 500 VAC rms between inner Guide for selecting a Backshell: and outer contacts sea level When ordering backshells, to avoid interference between the piggyback grommets which are used on all size 8 cavities and the backshell the below keepout dimensions must be adhered to. (based on existing arrangements) Suggested Numbering for Quadrax Contacts ORIENTATION KEY 1 1 2 Size A Dia min L min 4 17 .734 .540 2 4 3 3 19 .869 .540 21 .869 .540 PIN CONTACT SOCKET CONTACT MATING FACE MATING FACE 23 1.088 .540 Differential Pairs, contacts 1-3, 2-4. 25 1.234 .540 See page 243 for part number ordering of popularly used 38999 Series III connectors with 100 ohm quadrax contacts. Suggested Strain Relief - Insert Arrangements 9-5 or 19-18 with Quadrax Contacts Quadrax differential pairs are 1 and 3, 2 and 4. Due to the piggyback grommet interference with normal strain reliefs on the shell size 9 only, the recommended strain relief for the connector is: Amphenol part number TGW-R-5309-10 (OD Cad) or TGF-R-5309-10 (Electroless nickel) - shell size 9 only. For 19-18 insert pattern, recommended backshell: Glenair 367-221-NF. This is recommended due to the proximity of the size 8 contacts in relation to the shell. Also see Quadrax contacts for ARINC 600 and R27 Rack and Panel Connectors on pages 265 and 266. 224 Contact Amphenol Aerospace for more information at 800-678-0141 www.amphenol-aerospace.com Options 5015 83723 III 26482 Back- 22992 26500 eMI Filter Class L Crimp Rear Pyle Matrix Pyle Matrix 2 Others Shells Transient Release MatrixeMI Filter 26482 83723 III 26500 5015 22992 Back- Options Matrix 2 Matrix Pyle Pyle Crimp Rear Class L Transient Shells Others Release Matrix Quadrax Contacts for MIL-DTL-38999 Amphenol Aerospace Series III, Application Data TV-R Series, MIL-DTL-38999 Series III* Connectors 38999 QUADRAX CONTACTS FOR USE IN TV-R CONNECTORS III Contact Part Number HD Inner Crimping Tools Impedance Contact Electrical Cable Conductor Dualok (Termination Instruction Sheet)** (Ohms) Size Protocol (AWG) II Pin Socket Inner Contact Outer Contact Draka Fileca F-4703-3, F4704-4, I Filotex ET 2PC236, Filotex SJT ET2PF870, PIC Wire E50424 21-033384-021 21-033385-021 Ethernet, 1000 Base-T 24 ABS0972, Tensolite (L-2119-A) (L-2119-A) Gigabit Ethernet Accessories 23450/04090X-4(LD) Draka Fileca Aquacon F-4704-5, ABS1503 KD 24 Tensolite NF24Q100, NF24Q100-01, Herm/Seal 24443/9P025X-4(LD), S280W502-4, 24443/03130X-4(LD), PCB 24443/C20714X-4(LD), 24450/0120X-4(LD), NF24-2Q100, TYCO CEC- 21-033385-051 Ethernet, 1000 Base-T 21-033384-051 HIHg 24 RWC-18664, GORE GSC-01- (L-2119-D) (L-2119-D) Gigabit Ethernet SPeeD 81869-01, 24443/03166X-4(LD), Thermax T956-4T200, Pic Wire Fiber E51424, Thermax MX100Q-24, Optics NF24Q100-01-200C (Space), BMS13-72T03C04G024 Contacts Tensolite NF22Q100, Ethernet (100 Mbps), 21-033384-061 21-033385-061 Connectors NF22Q100-01, Thermax 956-5, 22 1000 Base-T Gigabit Cables (L-2119-H) (L-2119-H) GORE RCN 7688 Ethernet (1 Gbps) Tensolite NF26Q100, NF26Q100-01, 100 Ethernet (100 Mbps), 21-033384-071 21-033385-071 NF26-2Q100, PIC E51426, 26 1000 Base-T Gigabit (L-2119-AB) (L-2119-AB) Wirenetics W-3714-379 Ethernet (1 Gbps) 21-033384-141 21-033385-141 S280W502-4/BMS13- 24 72T03C04G024 (BACC47GM1) (BACC45GN1) Ethernet (100 Mbps), 21-033384-151 21-033385-151 Draka Fileca F-4704-6, 26 1000 Base-T Gigabit Gore RCN 8672 (L-2119-AW) (L-2119-AW) Ethernet (1 Gbps) M22520/2-01 Tensolite NF24Q100-01 (same as Ethernet (100 Mbps), with Positioner M22520/5-01 21-033384-161 21-033385-161 21-03338( ) 24 1000 Base-T Gigabit M22520/2-37 with Die Set (L-2119-BE) (L-2119-BE) 8 -51, uses EMI Piggyback) Ethernet (1 Gbps) or with Daniels M22520/5-45 Ethernet (100 Mbps), Positioner (Location A) 21-033384-171 21-033385-171 Gore RCN8513, JSFY18-3 22 1000 Base-T Gigabit K709 (L-2119-BN) (L-2119-BN) Ethernet (1 Gbps) Tensolite NF22Q100 Special Box Ethernet (100 Mbps), 21-033384-181 21-033384-181 pattern, only mates with 21-0333 22 1000 Base-T Gigabit (L-2119-BP) (L-2119-BP) ( )-181 Ethernet (1 Gbps) Serial FPDP Applications (2.5 Gbps) (Typical app Tensolite NF24Q100, NF24Q100-01 21-033384-191 21-033385-191 24 run at 150 Ohms) for 2.5 Gbps applications (L-2119-BS) (L-2119-BS) HDMI 1.3 Gore RCN 8647 21-033384-301 21-033385-301 24 USB2 (28433/02171LX-4) 21-033384-101 21-033385-101 90 USB2.0 (480 Mbps) Tensolite 24450/03089X-4(LD) 21-033384-211 21-033385-211 24 IEEE 1394B Firewire Gore RCN8647 JSFY02-1, JSFY18 21-033384-221 21-033385-221 24 IEEE 1394B Firewire 110 Gore RCN8487, JSFY18 21-033384-231 21-033385-231 24 IEEE 1394B Firewire Tensolite 24450/03089X-4(LD) Same as 21-03338( )-211 but Box 21-033384-241 21-033385-241 24 IEEE 1394B Firewire pattern, mates with 21-03338( )-241 only F-4703, ABS1503KD24 21-033384-281 21-033385-281 100 Meets EN3155-074 Tensolite 26473/02006X-4(LD)/Gore 21-033384-31 21-033385-031 RCN8328 (not for new designs, use 150 26 (L-2119-B) (L-2119-B) 21-033450/1 series) CHART CONTINUES ON NEXT PAGE Daniels crimping tools available from Daniels Mfg. Corp. 6103 Anno Ave., QUADRAX CONTACT DATA Orlando, FL 32809 Contacts are inserted by hand. Refer to termination instructions listed. Contacts are * Requires modified connector to accommodate keyed contacts. removed with a removal tool. Recommended tool is MIL-I-81969/14-06, Daniels DRK-264-8. **Termination instructions are packaged with each contact and can be Refer to termination instructions listed. Finish of mating contact parts: Contact part numbers found on-line at: www.amphenol-aerospace.com/serviceinstructions.asp shown in the chart above are supplied gold plated per ASTM B488 Type II, Code C, .000050 Consult Amphenol for current release of this contact or instruction sheet if applicable. min. thick over nickel plate per AMS-QQ-N-290, Class 2, .000030/.000150 thick. Test reports available for indicated protocols. Consult Amphenol Aerospace. Typical applications run at 150 Ohms Contact Amphenol Aerospace for more information at 800-678-0141 www.amphenol-aerospace.com 225