B C A D L K E M J F H G B C D A L N O E M K F J H G C 091 A Characteristics General Characteristics Standard Characteristics 1) Number of contacts 2 + 3 4 5 5 Stereo 6778 12 14 View on termination side 4 2 23 3 3 3 4 5 4 5 4 5 5 2 2 4 2 2 4 2 of male contact insert 7 2 1 3 1 3 1 3 1 3 6 8 1 4 6 1 5 1 5 1 6 7 6 7 Contact arrangement DIN EN 03-a 04-a 05-a 05-b 06-a 07-a 07-b 08-a 12-a 14-a 9 9 9 9 9 9 9 9 9 9 61076-2-106 2) Contact arrangement IEC 60130-9 99 99 99 Electrical Characteristics 3) Rated voltage IEC 60664-1 300 V 300 V 100 V 300 V 100 V 150 V (100 V ) (63 V ) (32 V ) (63 V ) (32 V ) (32 V ) Rated voltage UL 1977 250 V 60 V 3) Rated impulse withstand voltage IEC 60664-1 1500 V 1200 V 1500 V 1200 V (840 V) (500 V) (840 V) (500 V) 3) Pollution degree IEC 60664-1 1 (2) Installation category IEC 60664-1 I Insulation group IEC 60664-1 II, 400 CTI < 600 Current rating IEC 60512-5-2 5 A / + 40 C / + 104 F 3 A / + 40 C / UL 1977 please refer also to current derating curves page 59 + 104 F 10 4) Insulation resistance IEC 60512-3-1 > 10 Contact resistance IEC 60512-2-1 < 5 m Climatic Characteristics Climatic category IEC 60068-1 40 / 100 / 56 Temperature range IEC 60068-1 - 40 C ... + 100 C / - 40 F ... + 212 F Mechanical Characteristics IP-degree IEC 60529 IP 40 Insertion and withdrawal forces IEC 60512-13-2 25 N 30 N 35 N 50 N 55 N 60 N 50 N 90.oz 110.oz 125.oz 180.oz 200.oz 220.oz 180.oz Mechanical operation IEC 60512-9-1 Silver 500 mating cycles Gold 1000 mating cycles Materials Housing material coupling ring brass, strain relief, die cast, nickel plated Dielectric material thermoplastic 5) Contact plating silver plated / gold plated Further Characteristics Termination technique solder, crimp Wire gauge solder: 0,25 mm / 2 solder: 0,5 mm / 20 AWG 24 AWG 2 crimp: 2 - 6 pol (excluding 5S): 0,09 - 1,00 mm / 28 - 18 AWG crimp: 0,09-0,25 mm 2 crimp: 5S, 7, 7S and 8-pol.: 0,09 - 0,75 mm / 28 - 20 AWG / 28 24 AWG Flammability UL 94 V0 Locking system IEC 60130-9 DIN EN metal screw coupling tightening torque 0,7 Nm 61076-2-106 Caution: Do not connect or disconnect under load. Metal housing parts shall be securely incorporated to protected ground. 1) 2 contact version: contact loading 1+3 2) Edition 2000-05 3) values in brackets are according to DIN EN 61076-2-106 4) 8 under operating conditions >10 5) Remark for gold plated contacts: In order to avoid brittle inter-metallic connections, gold-plated terminals have to be tin-plated in the solder area. IEC 60 664 DIN VDE 0110 IEC 60 512-x DIN EN60 512-x IEC 60 130-9 DIN EN 60 130-9 IEC 61076-2-106 DIN EN 61076-2-106 = = = = 9X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Extraction, Removal & Insertion Tools category: Click to view products by Amphenol manufacturer: Other Similar products are found below : M8196914-08 768211-2 809-131 844751-2 8-59558-2 91018-1 12014013 12093647 1-21048-0 R282867020 12093078 12180559 1- 21048-6 12121897 DCF.91.405.5LT 1322 13549852 15314260 15313892 15350698 15350707 15430130 1643916-1 1-679532-0 1976593-3 OUTEXT-0321 2-1579008-3 2-1579008-4 229694-7 231106-1 241469 91040-3 91040-7 965004-000 965069-000 1738219-1 ET-JL05-16 FG 0300 146 3000 FIT-6 210S048 2-1579007-9 231879-1 CF-008025-000 312138-3 RJ11FODE 356-162 M8196914-10 4- 1579018-0 483249-1 5-1579007-2