DMD END 8 5 4 3 2 7 6 1 DRAWING CREATED WITH SW PART NUMBER DIM A DIM B REVISIONS 7840-001 5.20 4.30 REV DESCRIPTION DATE DWN 9 EC-12781 UPDATED TO MATCH INSP REV. LEVEL 3/1/18 GQ 7840-002 12.20 11.30 7840-003 23.62 22.72 7840-101 5.20 4.30 .239 7810-102 12.20 11.30 D D HARDWARE CONNECTED .155 TO GROUND WHEN MATED, .540 2 PLACES093 1.680 .270 1.500 cLGA HOUSING FORMATTER/J1 END .130 F25 F1 TOP BOLSTER A TAPPED M3 X 0.5 .180 TO CAPTIVATE SCREWS .180 A .350 .250 .197 C C .236 6 MAX A25 A1 M3 X 0.5 CAPTIVE LABEL, PAN HEAD USED AS PHILLIPS SCREW VARIABLE GOLD PLATED EXPOSED GROUND 2 PLACES THIS SIDE .0625 DIM B DIM A ASSEMBLY PIN FLEX CIRCUIT B B WHITE EPOXY INK .350 GOLD PLATED GROUND .094 MAX 2 PLACES THIS SIDE .394.059 .250 A1 .350 SECTION A-A SCALE 4 : 1 .180 .188 A25 DMD/J2 END 1.850 F1 F25 THIS DOCUMENT CONTAINS cLGA CONTACTS PROPRIETARY INFORMATION OF AMPHENOL INTERCON A AMPHENOL INTERCON SYSTEMS INC. SYSTEMS AND MAY NOT BE DISCLOSED, REPRODUCED OF OTHERWISE USED WITHOUT WRITTEN PERMISSION NOT SHOW THIS PAGE ETTERS, PA 17319 A THIRD ANGLE PROJECTION FOR CLARITY ALL DIMENSIONS AND TOLERANCE S PER NAME ASME Y14.5M-1994 cSTACK SYSTEM, FLEX ASSEMBLY INSPECTION TOLERANCES UNLESS SPECIFIED & BOLSTER PLATE, 150 POSITION OTHERWISE FIRST PIECE .010 2PLC SPC SIZE PROD CODE DRAWING NUMBER REV .005 3PLC IN-PROCESS .002 4PLC 043 7840 9 B C - 1 ANGLES SHEET SCALE OF FINISH MATERIAL - - CUSTOMER 1:1 1 5 4 3 5 2 6 18 5 4 3 2 7 6 1 DRAWING CREATED WITH SW 2.00 .182 THRU 2 PLC066 COMPONENT D D 1.200 THRU, KEEP-OUT AND 24 SPACES .050 SOLDERMASK OPENING DMD/J2 BOARD ONLY B R.05 .46 .180 .250 = 5 SPACES AT .050 .180 C C .055 A1 .066 BOARD EDGE THRU, .240 .050TYP FORMATTER/J1 NON-ACCUM BOARD ONLY090 .10 MIN .010 1.500 FINISHED VIA .066 THRU 1.680 R.014 RECOMMENDED P.C. BOARD LAYOUT .046 REF ALL .XXX DIMENSIONS .003 UNLESS OTHERWISE INDICATED B B .800 .800 .050 TYP NON-ACCUM 45 .018 MIN DETAIL B SCALE 8 : 1 NOTE 2 TYP THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF AMPHENOL INTERCON A AMPHENOL INTERCON SYSTEMS INC. SYSTEMS AND MAY NOT BE DISCLOSED, REPRODUCED OF OTHERWISE USED WITHOUT WRITTEN PERMISSION ETTERS, PA 17319 A THIRD ANGLE PROJECTION ALL DIMENSIONS AND TOLERANCE S PER NAME ASME Y14.5M-1994 cSTACK SYSTEM, FLEX ASSEMBLY ALLOWABLE BEND AREA INSPECTION TOLERANCES UNLESS SPECIFIED & BOLSTER PLATE, 150 POSITION OTHERWISE FIRST PIECE .010 2PLC BEND REQUIREMENTS NOTE 6 SPC SIZE PROD CODE DRAWING NUMBER REV .005 3PLC IN-PROCESS .002 4PLC 043 7840 9 B C - 1 ANGLES SCALE 1:1 SHEET SCALE OF FINISH MATERIAL - - CUSTOMER 3:1 2 5 4 3 5 2 6 1