PC16SH07CP06103A2020CTA Amphenol

16 mm Carbon Potentiometer PC-16 FEATURES Carbon resistive element. IP54 protection according to IEC 60529. Polyester substrate. Modular gang type (up to 4). Self extinguishable material UL 94-V0. Upon request: Metalic support. Stereo matching. Switch. Nut & washer. Bushless & shaftless models. Bushless version Assemblies with wires and connectors. MECHANICAL SPECIFICATIONS ELECTRICAL SPECIFICATIONS Range of values* Mechanical rotation angle: 300 5 Electrical rotation angle: 280 20 Standard tolerance*: 20% 30% Torque: 0.5 to 1.5 Ncm. (0.7 to 2.1 in-oz) Max. Voltage: 250 VDC (lin) 125 VDC (no lin) Stop torque: > 40 Ncm. ( >56 in-oz) Nominal Power 50C (122F) (see power rating curve) 0.2 W (lin) 0.1 W (no lin) Max. torque nut (binding out): < 80 Ncm. (112 in-oz) Taper* Lin Log Alog (Log. & Alog. only Rn 1K). Thrust and pull in the shaft: > 25 N Residual resistance*: 5 5 Equivalent Noise Resistance: * Others check availability. Operating temperature**: 25C + 70C (13F + 158F) ** Up to 85C depending on application. HOW TO ORDER OPTIONAL EXTRAS PC-16 D H 10 I M06 203 A 2020 0 Mounting style Value Tolerance Mounting brackets Switch Serie Terminals H= Horizontal I = PCB 0505 = 5% PC-16 M1 I = PCB V = Vertical C = Solder Lugs 1010 = 10% M2 C = Solder lugs (See note 1) 2020 = 20% (See note 7) Shafts (See note 9) 3030 = 30% M04 Stereo matching Model (See note 4) (See note 5) M06 M07 3D = 3dB Nuts & Washers S =Single Bushing diameter M11 4D = 4dB Taper Shafts spec. leng. -TA = loose nut & washer D =Tandem 6D = 6dB 07 = M7 M17 MTA=assembled nut & 10 = M10 A = Linear XX.X (See note 8) T =Triple washer P01 B = Log. = SC Bushless -T- = loose nut (See notes 6,9) C =Quad. C = Alog. P22 (See note 2) MT- = assembled nut --- (See note 10) (See note 9) (See note 3) Others tapers on request NOTES: (1) Mounting style: Type is only available in model potentiometer and with printed circuit terminals. (2) Bushings: Type10 has two paralell flat surfaces for avoiding rotation. Bushless option only available for single model. (3) M07 shaft is only available with M10 bushing. --- = no shaft (4) Value: Code: 10 1 Number of zeros 2 first digits of the value. In models,,, with different values, they will be asked by drawings. Example: +7% Code: (5) Tolerance (non standard), upon request. 07 05 negative tolerance -5% positive tolerance (6) Shaft special length: Only for special length and plain shafts (not knurled). Example: Shaft 6.35 L= 24.5 M07 ..... 24.5 special length NOTE: Maximun length recommended: L = 45 shafts (7) Mounting brackets: Only applicable for model, mounting and without switch. (8) Stereo matching: not available for single models. Maximun will be: 3dB for model 4dB for model 6dB for model (9) Not available for Bushless version. (10) Switch option not available with antilog taper. 69 www.piher.netSTANDARD OPTIONS HOW TO ORDER CUSTOM DRAWING Shaft length .................................. 0 Standard Length Mounting brackets ........................ Without mounting brackets PC-16 S V + DRAWING NUMBER (Max. 16 digits) Stereo matching ........................... Only on request (see note 8) This way of ordering should be used for options which are not included Switch ........................................... No switch in theHow to orde standard and optional extras. Nut & washer ................................ Without nut and washer MODELS -0.1 6.5 7.5 7.5 7.5 1.1 E S M10 x 0.75 A S M10 x 0.75 E A 9 8 9 + + 0.5 + 0.5 0.5 45 16 45 8 16 30.5 5 (wiper) 6.5 7.5 7.5 7.5 S 5 5 +0.1 E A (final) (initial) 1.3 Mounting surface S D T C +0.1 10 1.3 PC-16 S/D/T/C..H... PC-16 SV ......... METALLIC SUPPORT 6.5 2.5 7.5 6.5 10 20 20 -0.1 -0.1 1 1.1 M10 x 0.75 M10 x 0.75 9 9 + + 0.5 0.5 16 16 45 8 45 8 6.5 10 6.5 2.5 7.5 Mounting surface Mounting surface +0.1 1.3 +0.1 PC-16 SH......M1 PC-16 SH....M2 1.3 BUSHINGS 8 8 M7 x 0.75 M10 x 0.75 0.6 0.6 8 9 16 16 16 17 07 10 EXAMPLES OF BUSHLESS VERSION 3.1 3.1 3.1 thickness = 0.5 16 7.5 16 16 7.5 7.5 Download STEP files here: