PT10LV10500A5030 Amphenol

10 mm Carbon Potentiometer PT-10 FEATURES Carbon resistive element IP54 protection according to IEC 60529 Polyester substrate Also upon request: Wiper positioned at 50% or fully clockwise. Supplied in magazines for automatic insertion. Long life model for low cost control potentiometer applications Self extinguishable plastic UL 94V-0 Cut track option Special tapers Mechanical detents Low torque version Special switch option SMD versin available (PS-10) 3% Linearity and 100K cycles mechanical life MECHANICAL SPECIFICATIONS ELECTRICAL SPECIFICATIONS Range of values (*) Mechanical rotation angle: 235 5 Electrical rotation angle: 220 20 Tolerance (*): 20% Torque: 0.4 to 2 Ncm. 30% (0.6 to 2.7 in-oz) Max. Voltage: 200 VDC (lin) 100 VDC (no lin) Stop torque: > 5 Ncm. ( >7 in-oz) Nominal Power 50C (122F) (see power rating curve) Life(*): Up to 10K cycles 0.15 W (lin) 0.07 W (no lin) Taper (*) (Log. & Alog. only Rn 1K) Lin Log Alog. Residual resistance(*): Equivalent Noise Resistance: Operating temperature(**): -25C + 70C (-13F + 158F) (*) Others upon request (**) Up to 85C depending on application HOW TO ORDER OPTIONAL EXTRAS PT 10 L H01 101 A 2020 S Mounting Code Torque Series Taper Life Detents Shaft/Thum. Shaft/rotor colour Method PAI RO = Red PT-10 H01 H2.5 A = Lin. E= Long life 01 = Fig. 1 = Standard PAM NE = Black 02 = Fig. 2 B = Log. H05 H5 VE = Green (See note 5) PAF L= Low Torque C = Alog. AM = Yellow Rotors H02 H2.5P P1I AZ = Blue (See note 9) P1F 17 = Fig. 17 H10 H5P B MA = Brown P02 G . V05 V5 (See note 10) GR = Grey . Value K . NA = Orange Tolerance V10 V L P16 CR = Cream 101 = 100 M V11 VP 2020 = 20% (See note 8) R V13 VJ 504 = 500 K 3030 = 30% W Flammability Wiper position Cut track Magazine X (See note 2 / (See note 4) SMD version Y 505 = 5 M I = Non flammable PCI = Initial PM = 50% available: see T Z 000 = CM PF = Final product PS-10) PCF = Final (See note 7) (See note 1) (See note 6) (See note 3) NOTES: (1) adjustment only available on versions. Rotor only available in purple (shaft/rotor colourV). (2) Terminals styles: & are crimped. V=Vertical adjust H=Horizontal Adjust (3) Value Example: Code: 10 1 000 = CM = Switch version (contact us) Numb of zeros First two digits of the value. (4) Non standard tolerance, upon request. Example: +7% Code: 07 05 -5% negative tolerance (5) Standard = 1000 cycles Long = 10K cycles positive tolerance Others upon request. (6) Magazines: not available with the H10, V05 and V13 models, nor with adjustment types X, W, Y, Z. (7) Non flammable: housing, rotor and shaft. According to UL 94V-0 Potentiometer without shaft: only rotor Potentiometer with shaft: only shaft (8) Colour shaft/rotor: Cream colour only available in standard plastic. (9) Low Torque: 1 Ncm No detent option available for low torque models. (10) If you wish to use your own custom plastic shaft/knob/actuator please contact Piher for advice about compatible materials. NOTE: The information contained here should be used for reference purposes only. www.piher.net v051015 391.7 2 HOW TO ORDER CUSTOM DRAWING STANDARD OPTIONS Cut track No Detents None Packing Bulk PT-10 LH 01 + DRAWING NUMBER (Max. 16 characters) Non flammable No Rotor colour White This way of ordering should be used for options which are not included Shaft colour Natural in theHow to orde standard and optional extras. Wiper position Initial Torque Standard Life 1000 cycles ROTORS Without shaft With shaft 2.2 2 2 0.8 L L L = Screwdriver M = Hexagonal G = Hexagonal K = Cross slot R B X = W = thru hole thru hole thru hole thru hole Adjustable from Adjustable from Wipers positioned at 50% collector side terminal side With thumbwheel 6.5 6.5 0.8 0.8 1.95 3.75 Y = Adjustable from terminal side Z = Adjustable from collector side MOUNTING METHODS v = horizontal mount vertical adjust h = vertical mount horizontal adjust + + + +0.1 0.2 0.1 0.2 4.8 4.8 10.3 10.3 +0.1 2.5 1.3 4 S A E A E +0.1 5 1.3 + 0.2 +0.1 S 5 6 3.5 2.5 2.5 2.5 1 + 0.1 1 v (10) A = Initial S = Wiper E = Final h (2.5) A = Initial S = Wiper E = Final + + 0.1 + 0.1 +0.2 0.2 4.8 10.3 4.8 10.3 5 +0.1 1.3 3 +0.1 1.3 5 + 0.2 6.5 +0.1 5 3.5 5 2.5 2.5 1 + 0.1 1 v (5) h (5) NOTE = Please note relative terminal positions Crimped terminals when ordering non linear tapers. Detail A + 0.2 +0.2 6 6 - 0.1 9.3 9.3 0.9 Mod. J Mod. P www.piher.net 40 51.4 2 2.1 2.5 2.5 5 5 3.5 7 5 10 3 2.2 3.5 3.5 +0.1 0.7 2.5 2.5 5 5 5 10 1.6 +0.2 +0.2 12.1 12.1 3.5 7 3 +0.2 + 0.2 7 3.5 7 3.5 + 0.3 - 0.1 1.6 5 5