PT15LH06-253A2020 Amphenol

15 mm Carbon Potentiometer PT-15 FEATURES - Carbon resistive element. - IP54 protection according to IEC 60529. - Polyester substrate. - Also upon request: Long life model for low cost control pot. applications Low torque option Supplied in magazines for automatic insertion. Wiper positioned at initial, 50% or fully clockwise. Self extinguishable plastic UL 94V-0. Cut track option. Special Tapers. Mechanical detents. ELECTRICAL SPECIFICATIONS MECHANICAL SPECIFICATIONS Range of values*: Mechanical rotation angle: 265 5 100 Rn 5M (Decad. 1.0 - 2.0 - 2.2 - 2.5 -4.7 -5.0) 240 5 available upon request. Tolerance*: 100 Rn 1M : 20% Electrical rotation angle: 240 20 1M Rn 5M : 30% 0.5 to 2.5 Ncm. Torque: Max. Voltage: 250 VDC (lin) 125 VDC (no lin) (0.7 to 3.4 in-oz) Nominal Power 50C (122F) (see power rating curve) Stop torque: > 10 Ncm. ( >14 in-oz) 0.25 W (lin) 0.12 W (no lin) Life*: Up to 100K cycles Lin Log Alog. Taper*: (Log. & Alog. only Rn 1K) Residual resistance*: 0.5% Rn (5 min.) 3% Rn (3 min.) Equivalent Noise Resistance: * Others: check availability. Operating temperature**: 25C + 70C (13F + 158F) ** Up to 85C depending on application. HOW TO ORDER OPTIONAL EXTRAS - PT15 L H01 - 223 A 2020 - S Mounting Series Code Taper Life Detents Flammability Wiper position Method H01 H2.5 PAI E= Long life PM = 50% A = Lin. I= non flammable H05 H5 PAM U= Extra Long life PF = Final B = Log. Rotor H25 HC5 PAF (See note 6) C = Alog. H06 B (See note 5) P1I C H02 H2.5P P1F F Shaft/rotor colour Magazine H10 H5P P02 G . V02 V12.5 Value Tolerance . RO=Red L T . V12 VA NE=Black 0505 = 5% M P38 V15 V15 (See note 9) VE=Green N 0707 = 7% V20 VL15 223 = 22 K AM=Yellow R V17 V17.5 1010 = 10% Cut track Shaft/Thum. Torque AZ=Blue T 504 = 500 K V18 D 2020 = 20% MA=Brown X V24 VD15 01 Fig. 1 = Standard 505 = 5 M PCI = Initial GR=Grey 3030 = 30% W V21 V12.5P L = Low torque NA=Orange (See note 4) Y V22 VAP PCF= Final (See note 3) CR=Cream V23 V15P Z (See note 8) 28 Fig. 28 (See note 7) V25 V17.5P (See note 1) (See note 10) (See note 2) NOTES: (1) adjustment only available on versions. Standard colour for the T rotor: Orange. (2) Terminal styles: are crimped terminals. V24 terminals material: brass. V=Vertical adjust H=Horizontal Adjust (3) Value: Example: Code: 10 1 Example: +7% Code: 07 05 -5% Numb of zeros. negative tolerance First two digits of the value. positive tolerance (4) Non standard tolerance: check availability. (5) Life Standard: 1K cycles. Long life: 10K cycles. Extra long life: 100K cycles (Only for low torque versions. To be studied case by case.) (6) Non flammable: housing, rotor and shaft. According to UL 94V-0 (7) Colour shaft/rotor: Potentiometer without shaft: only rotor Potentiometer with shaft: only shaft Cream colour only available in standard plastic (8) Low torque: 1.5Ncm. No detent option available for low torque models. (9) Magazines (35 pcs/mag): available for VA (12.5), V (12.5), V (12.5P), V (15), V15 (P) and H models. For more information please contact your nearest Piher supplier. (10) If you wish to use your own custom plastic shaft/knob/actuator please contact Piher for advice about compatible materials. 1 www.piher.net 0.05 4.05 3.05 0.05 3.8 -0.1 42.5 42.5 HOW TO ORDER CUSTOM DRAWING STANDARD OPTIONS Cut track ......................................................... No Detents ............................................................. None (Max. 16 digits) PT-15 LH 01 + DRAWING NUMBER Non flammable ................................................... No Rotor colour ........................................................ White This way of ordering should be used for options which are not included Shaft colour ...................................................... Natural in theHow to orde standard and optional extras. Wiper position ................................................... Initial Torque ............................................................ Standard Terminals material ................................................ Steel Life .................................................................. 1000 cycles ROTORS Wipers positioned at initial (without shaft) Wipers positioned at 50% (without shaft) 0.05 0.05 0.05 4.05 4.02 3.35 1.2 Wiper Wiper position position 0.05 4.4 L = N = G = M = Rotor C Rotor F Rotor R Rotor T Screw driver Removable shaft Removable shaft Hexagonal thru hole or thumbwheel or thumbwheel thru hole With shaft With thumbwheel +0.3 +0.3 6 7.5 7.5 +0.5 +0.5 L L Y = Z = Adjustable from Adjustable from terminal side collector side X = Adjustable from collector side W = Adjustable from terminal side VERTICAL MOUNT - HORIZONTAL ADJUST H (2.5) 0.2 0.2 B 0.2 0.2 6 15 +0.1 6 15 +0.1 1.3 1.3 A S E 2.5 4 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 5 5 2.5 1 4,4 4.4 4 1 A = Initial S = Wiper E = Final H (5) +0.2 0.2 0.2 +0.2 H C5 6 15 +0.1 6 15 +0.1 1.3 1.3 5 5 +0.1 +0.1 +0.1 5 5 5 1 +0.1 +0.1 +0.1 5 5 5 1 Check availability. 6 15 Download STEP files here: 1.3