XBOPL5034CR Amphenol

10 mm Carbon Potentiometer PT-10 FEATURES Carbon resistive element Dust proof enclosure Polyester substrate Also upon request: Wiper positioned at 50% or fully clockwise. Supplied in magazines for automatic insertion. Long life model for low cost control potentiometer applications Self extinguishable plastic UL 94V-0 Cut track option Special tapers Mechanical detents Low & extra low torque versions Special switch option 3% Linearity and 100K cycles mechanical life MECHANICAL SPECIFICATIONS ELECTRICAL SPECIFICATIONS Mechanical rotation angle: 235 5 Range of values (*) Electrical rotation angle: 220 20 Tolerance (*): 20% Torque: 0.4 to 2 Ncm. 30% (0.6 to 2.7 in-oz) Max. Voltage: 200 VDC (lin) 100 VDC (no lin) Stop torque: > 5 Ncm. ( >7 in-oz) Nominal Power 50C (122F) (see power rating curve) Life*: Up to 10.000 cycles 0.15 W (lin) 0.07 W (no lin) Taper (*) (Log. & Alog. only Rn 1K) Lin Log Alog. * Others upon request Residual resistance(*): Equivalent Noise Resistance: Operating temperature**: -25C + 70C (-13F + 158F) (*) Others upon request ** Up to 85C depending on application HOW TO ORDER OPTIONAL EXTRAS PT 10 L H01 101 A 2020 S Mounting Code Life Detent Shaft/Thum. Shaft/rotor colour Torque Series Taper Method RO = Red PT-10 H01 H2.5 A = Lin. E= Long life See PT s 01 = Fig. 1 = Standard NE = Black with detents 02 = Fig. 2 B = Log. H05 H5 VE = Green (See note 5) data sheet L= Low Torque C = Alog. H02 H2.5P AM = Yellow Rotors AZ = Blue (See note 9) 17 = Fig. 17 H10 H5P MA = Brown G V05 V5 (See note 10) GR = Grey Value L NA = Orange Tolerance V10 V M CR = Cream 101 = 100 V11 VP K 2020 = 20% (See note 8) X V13 VJ 504 = 500 K 3030 = 30% W Flammability Wiper position Cut track Magazine (See note 2) Y (See note 4) Z 505 = 5 M I = Non flammable PCI = Initial PM = 50% T R PCF = Final PF = Final (See note 3) (See note 7) (See note 6) (See note 1) NOTES: (1) adjustment only available on versions. Rotor only available in purple (shaft/rotor colourV). (2) Terminals styles: & are crimped terminals. V=Vertical adjust H=Horizontal Adjust Example: Code: (3) Value 10 1 Numb of zeros First two digits of the value. (4) Non standard tolerance, upon request. Example: +7% Code: 07 05 -5% negative tolerance Up to 10.000 cycles. (5) Others upon request. positive tolerance (6) Magazines: not available with the H10, V05 and V13 models, nor with adjustment types X, W, Y, Z. (7) Non flammable: housing, rotor and shaft. According to UL 94V-0 (8) Colour shaft/rotor: Potentiometer without shaft: only rotor Potentiometer with shaft: only shaft Cream colour only available in standard plastic. (9) Low Torque: 0.25 to 1 Ncm (per pot.) No detent option available for low torque models. (10) If you wish to use your own custom plastic shaft/knob/actuator please contact Piher for advice about compatible materials. NOTE: The information contained here should be used for reference purposes only. 39 www.piher.net0.05 2 HOW TO ORDER CUSTOM DRAWING STANDARD OPTIONS Cut track No Detents None PT-10 LH 01 + DRAWING NUMBER (Max. 16 characters) Packing Bulk Non flammable No Rotor colour White This way of ordering should be used for options which are not included Shaft colour Natural in theHow to orde standard and optional extras. Wiper position Initial Torque Standard ROTORS 0.05 0.05 Without shaft 2.2 2 With shaft 0.05 0.05 2 0.8 L = Screwdriver M = Hexagonal G = Hexagonal K = Cross slot L L R thru hole thru hole thru hole thru hole X = W = Wipers positioned at 50% Adjustable from collector side Adjustable from terminal side With thumbwheel 6.2 6.2 0.8 0.8 1.95 3.45 Y = Adjustable from terminal side Z = Adjustable from collector side MOUNTING METHODS v = horizontal mount vertical adjust h = vertical mount horizontal adjust +0.1 +0.2 +0.1 +0.2 4.5 10.3 4.5 10.3 +0.1 2.5 1.3 S 4 E A E +0.1 A 5 1.3 +0.2 +0.1 S 2.5 5 6 3.5 2.5 2.5 1 +0.1 1 v (10) A = Initial S = Wiper E = Final h (2.5) A = Initial S = Wiper E = Final +0.1 +0.1 +0.2 +0.2 4.5 10.3 4.5 10.3 5 +0.1 1.3 3 +0.1 1.3 5 +0.2 6.5 +0.1 5 3.5 2.5 2.5 5 1 +0.1 1 v (5) h (5) NOTE = Please note relative terminal positions Crimped terminals when ordering non linear tapers. Detail A +0.2 +0.2 6 6 -0.1 9.3 9.3 0.9 Mod. J Mod. P 40 www.piher.net - 0.1 2.1 2.5 2.5 5 5 3.5 7 5 10 3 3.5 3.5 + 0.1 2.2 2.5 2.5 5 5 5 10 + 0.1 0.7 0.05 1.6 +0.2 +0.2 12.1 12.1 3.5 7 3 + + 0.2 0.2 3.5 7 3.5 7 + 0.3 -0.1 1.6 5 5