Data Sheet ACD-10 PLUS 600A Clamp-On Multimeter Amprobes ACD-10 PLUS meter offers thinner jaws over standard clamp meters. Allowing access to tight measurement areas and still accommodating conductors up to 25 mm. It also measures Capaci- tance and Frequency. Frequency is measured by either jaws or test leads. Very versatile clamp multimeter. AC & DC Voltage to 600V AC Current to 600A Thin Jaws, only 10mm (0.4) thick Resistance to 40M W Continuity Buzzer Capacitance to 3000 uF Frequency measurement No hassle In rush current warranty Hold & Maximum reading functions No waiting. Accommodates conductors up to 26mm (1.02) in diameter No shipping Auto ranging charges. Auto power off Our commitment to high-quality products Rubber over-molded case and customer service Overload protected is demonstrated by our industry exclusive No Hassle warranty. In the unlikely event that an Amprobe Test Tool requires warranty service, any of our local dealers are authorized to replace it, on the spot. (note: 500 MSLP limit) 600V Amprobe Test Tools www.Amprobe.comData Sheet ACD-10 PLUS 600A Clamp-On Multimeter General Specifications Display: 3-3/4 digits 4000 counts LCD display Update Rate: 3 per second nominal Polarity: Automatic Operating Temperature: 0 C to 40 C < 80% RH for temperature up to 31 C decreasing linearly to 50% RH at 40 C Altitude: Operating below 2000m Indoor use Storage Temperature: -20 C to 60 C, < 80% RH (with battery removed) Temperature Coefficient: nominal 0.15 x (specified accuracy)/C (0 C ~ 18 C or 28 C ~ 40 C) Low Battery: Below approx. 2.4V Power Supply: 3V coin battery IEC-CR2032 Power Consumption: 2.8 mA typical except that 3.3 mA typical for ACA function APO Timing: Idle for 30 minutes APO Consumption: 5 A typical Dimension: 190 x 63 x 32 mm (7.4 x 2.5 x 1.3 in) Weight: 139 gm approx Jaw opening & Conductor diameter: max 26 mm Special Features: 30ms Max Hold Data Hold Relative Zero mode Safety: Meets EN61010-2-032, UL61010B-2-032, IEC61010-1 2nd Ed., EN61010-1 2nd Ed., UL61010-1 2nd Ed. CAT III-600 Volts ac & dc Pollution degree : 2 EMC: Conforms to EN61326-1. This product complies with requirements of the following European Community Directives: 89/ 336/ EEC (Electromagnetic Compatibility) and 73/ 23/ EEC (Low Voltage) as amended by 93/ 68/ EEC (CE Marking). However, electrical noise or intense electromagnetic fields in the vicinity of the equipment may disturb the measurement circuit. Measuring instruments will also respond to unwanted signals that may be present within the measurement circuit. Users should exercise care and take appropriate precautions to avoid misleading results when making measurements in the presence of electronic interference. Electrical Specification Accuracy (23 C 5 C & < 75% R.H.) Function Range Accuracy DC Voltage 400.0 mV ( 0.3% + 4 digits) 4.000, 40.00, 400.0 V ( 0.5% + 3 digits) 600 V ( 1.0% + 4 digits) NMRR: >50 dB 50/60Hz CMRR: >120 dB DC, 50/60 Hz, Rs=1 k W Input Impedance: 10 M W, 30 pF nominal (1000 M W for 400.0 mV range) Transient protection: 6.5 kV (1.2/50 s surge) AC Voltage (50Hz ~ 500Hz) 4.000, 40.00, 400.0 V ( 1.5% + 5 digits) 600 V ( 2.0% + 5 digits) CMRR: >60dB DC to 60 Hz, Rs=1 k W Maximum Crest Factor: < 1.75 : 1 at full scale & < 3.5 : 1 at half scale limited to fundamental and harmonics, that fall within the meter specified AC bandwidth for non-sinusoidal waveforms Input Impedance: 10 M W, 30 pF nominal Transient protection: 6.5 kV (1.2/50s surge) ACD-10 Plus: Average Sensing Amprobe Test Tools www.Amprobe.com