ADP130-1.8-EVALZ Analog Devices

350 mA, Low V , Low Quiescent Current, IN CMOS Linear Regulator Data Sheet ADP130 FEATURES TYPICAL APPLICATION CIRCUITS 350 mA maximum output current V = 1.8V V = 1.2V IN OUT 1 VIN VOUT 5 Input voltage supply range + + 1F 1F ADP130 V = 2.3 V to 5.5 V BIAS 2 GND V = 1.2 V to 3.6 V IN 2.3 V < V < 3.6 V, VIN can be tied to VBIAS IN ON V = 3.6V BIAS 3 EN 4 VBIAS Very low dropout voltage: 17 mV 100 mA load OFF + 1F Low quiescent current: 25 A no load Low shutdown current: <1 A Figure 1. 1% accuracy 25C Excellent PSRR performance: 70 dB 10 kHz Excellent load/line transient response V = 2.8V IN V = 1.8V OUT Optimized for small 1 F ceramic capacitors 1 VIN 5 VOUT + + Current limit and thermal overload protection 1F 1F ADP130 Logic controlled enable 2 GND 5-lead TSOT package ON V = 5V BIAS 3 EN VBIAS 4 OFF APPLICATIONS + 1F Mobile phones Digital camera and audio devices Figure 2. Portable and battery-powered equipment Post dc-to-dc regulation GENERAL DESCRIPTION The ADP130 is a low quiescent current, low dropout linear regu- The ADP130 is optimized for stable operation with small 1 F lator. It is designed to operate in dual-supply mode with an input ceramic output capacitors. The ADP130 delivers good transient voltage as low as 1.2 V to increase efficiency and provide up to performance with minimal board area. 350 mA of output current. The low 17 mV dropout voltage at The ADP130 is available in fixed output voltages ranging from : a 100 mA load improves efficiency and allows operation over 0.80 V to 3.0 V. a wider input voltage range. The ADP130 has a typical internal soft start time of 200 s. Short- A dual-supply power solution typically improves conversion circuit protection and thermal overload protection circuits efficiency over a single-supply solution because the higher VBIAS prevent damage in adverse conditions. The ADP130 is available supply powers the part, and the lower VIN supply delivers current in a tiny 5-lead TSOT package for the smallest footprint solution to to the load. The power dissipated in the device is thereby reduced. meet a variety of portable power applications. Rev. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. rights of third parties that may result from its use. Specifications subject to change without notice. No Tel: 781.329.4700 www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Fax: 781.461.3113 20082012 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. 06963-002 06963-001ADP130 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Typical Performance Characteristics ..............................................7 Applications ....................................................................................... 1 Theory of Operation ...................................................................... 12 Typical Application Circuits ............................................................ 1 Applications Information .............................................................. 13 General Description ......................................................................... 1 Capacitor Selection .................................................................... 13 Revision History ............................................................................... 2 Undervoltage Lockout ............................................................... 14 Specif icat ions ..................................................................................... 3 Enable Feature ............................................................................ 14 Input and Output Capacitor: Recommended Specifications.. 4 Current Limit and Thermal Overload Protection ................. 15 Absolute Maximum Ratings ............................................................ 5 Thermal Considerations ............................................................ 15 Thermal Data ................................................................................ 5 Junction Temperature Calculations ......................................... 16 Thermal Resistance ...................................................................... 5 PCB Layout Considerations ...................................................... 17 ESD Caution .................................................................................. 5 Outline Dimensions ....................................................................... 18 Pin Configuration and Function Descriptions ............................. 6 Ordering Guide .......................................................................... 18 REVISION HISTORY 6/12Rev. B to Rev. C Changed EN to GND Absolute Maximum Rating from 0.3 V to +6 V to 0.3 V to VBIAS.......................................................... 5 Changes to Ordering Guide .......................................................... 18 5/10Rev. A to Rev. B Changes Figure 1 and Figure 2 ....................................................... 1 Updated Outline Dimensions ....................................................... 18 Changes to Ordering Guide .......................................................... 18 3/09Rev. 0 to Rev. A Changes to Table 2 ............................................................................ 4 Changes to Figure 18 to Figure 21 .................................................. 9 Changes to Figure 22 to 26 ............................................................ 10 7/08Revision 0: Initial Version Rev. C Page 2 of 20