EVALUATION KIT AVAILABLE MAX14883E CAN Transceiver with 60V Fault Protection and Selectable Polarity General Description Benefits and Features The MAX14883E fault-protected, high-speed Control Integrated Protection for Robust Communication Area Network (CAN) transceiver is optimized for industrial 60V Fault Tolerant CANH and CANL network applications. This device features 60V fault High ESD Protection on CANH and CANL - 22kV Human Body Model protection, a 25V functional common mode input range, and high 10kV ESD protection (contact discharge) on - 15kV IEC 61000-4-2 Air Gap - 10kV IEC 61000-4-2 Contact Discharge the CANH and CANL bus. The device operates from a single 5V supply (V ) and includes a logic-level supply CC Flexible Logic Interface Simplifies Designs input (V ) for interfacing with 1.8V to 5V logic. L 1.71V to 5.5V Logic-Supply (V ) Range L The MAX14883E features a polarity selection input (POL) High Integration Allows Simplified Network that swaps the CANH and CANL I/Os, allowing for software Configuration correction of cross-wired field cables. Polarity Control The MAX14883E operates at the maximum CAN high- Dominant Timeout Protection speed data rate, allowing up to 1Mbps on small networks. Capable of Data Rates Up to 1Mbps The maximum speed on large networks may be limited by Applications capacitive loading and other factors. Industrial Controls The transceiver includes a transmitter dominant timeout Building Automation (t ) to prevent bus lockup caused by controller error DOM or by a fault on the TXD input. When TXD remains in the HVAC dominant state (low) for longer than t , the driver is DOM Switch Gear switched to the recessive state, releasing the bus. The MAX14883E is available in a narrow, 8-pin SOIC package and operates over the -40C to +125C Ordering Information appears at end of data sheet. temperature range. Simplified Block Diagram VDD VDD VL MAX14883E TXD-DOMINANT TXD TIMEOUT PROTECTION CANH LEVEL SHIFTER PROTECTION CANL RXD POLARITY SELECT POL CONTROL GND 19-8736 Rev 0 12/16MAX14883E CAN Transceiver with 60V Fault Protection and Selectable Polarity Absolute Maximum Ratings (All voltages referenced to GND, unless otherwise noted) Continuous Power Dissipation V ..........................................................................-0.3V to +6V Single-Layer Board (T = +70C, derate 5.9mW/C DD A CANH or CANL (Continuous) .................................-63V to +63V above +70C.) ..........................................................470.6mW TXD, POL ..................................................................-0.3V to 6V Multilayer Board (T = +70C, derate 7.6mW/C A V ............................................................. -0.3V to (V + 0.5V) above +70C.) ..........................................................606.1mW L DD RXD ................................................................-0.3V to V + 0.3V Operating Temperature Range ............................-40C to 125C L Junction Temperature ......................................................+150C Storage Temperature Range ............................ -60C to +150C Lead Temperature (soldering, 10s) ................................+300C Soldering Temperature (reflow) .......................................+260C Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Package Information 8 SOIC PACKAGE CODE S8+4 Outline Number 21-0041 Land Pattern Number 90-0096 Thermal Resistance, Single-Layer Board: Junction to Ambient ( ) 170 JA Junction to Case ( ) 40 JC Thermal Resistance, Four-Layer Board: Junction to Ambient ( ) 132 JA Junction to Case ( ) 38 JC For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a +, , or - in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer board. For detailed information on package thermal considerations, refer to www.maximintegrated.com/thermal-tutorial. Maxim Integrated 2 www.maximintegrated.com