Evaluates: MAX16031 19-1540 Rev 0 11/07 MAX16031 Evaluation Kit General Description Features The MAX16031 evaluation kit (EV kit) provides a proven USB Interface to Host PC printed-circuit board (PCB) layout that facilitates evalu- Easy-to-Use GUI Software ation of the MAX16031 EEPROM-based system monitor with nonvolatile fault memory. This EV kit is a fully Facilitates Programming of MAX16031s on assembled and tested surface-mount board. Prototype Boards 2 The EV kit includes an on-board USB-to-JTAG and I C LEDs Indicate Each Outputs State interface facilitating communications between the host PC and the MAX16031. A DAC connected to the moni- On-Board DAC Simulates Monitored Voltages toring inputs and the status LEDs connected to each Convenient Test Points and Headers for Easy programmable output make it easy to evaluate the vari- Evaluation ous monitoring functions of the MAX16031. Fully Assembled and Tested This EV kit data sheet assumes basic familiarity with the MAX16031. Refer to the MAX16031/MAX16032 IC data Ordering Information sheet for more detailed information. PART TYPE MAX16031EVKIT+ EV Kit +Denotes lead-free and RoHS-compliant. Component List DESIGNATION QTY DESCRIPTION DESIGNATION QTY DESCRIPTION 2.2F 20%, 10V X5R ceramic 1F 10%, 10V X5R ceramic C1, C2, C4, capacitors (0805) capacitors (0805) C112, C113 2 5 TDK C2012X5R1A225M C100, C108 TDK C2012X5R1A105K Taiyo Yuden LMK212BJ225MG KEMET C0805C105K4PAC 0.1F 10%, 25V X7R ceramic 33pF 5%, 50V C0G ceramic capacitors (0805) capacitor (0603) C3, C5, C6 3 C114 1 TDK C2012X7R1E104K TDK C1608C0G1H330J Taiyo Yuden TMK212B104KT Taiyo Yuden UMK107CG330JZ C7 0 Not installed, capacitor (0805) EXT PWR 1 Test point, red F100 1 500mA fast-acting fuse (2405) 0.1F 10%, 25V X7R ceramic C101, C102, capacitors (0603) GND, REF 2 Test points, black 3 C103 TDK C1608X7R1E104K J1, J2, J4 3 3-pin headers Taiyo Yuden TMK107BJ104KA J3 1 2-pin header 18pF 5%, 50V C0G ceramic J100 1 2 x 3-pin header C104, C105, capacitors (0603) 4 LED1LED7, C106, C107 TDK C1608C0G1H180J 11 Green LEDs (1206) LE D 100LED 103 Taiyo Yuden UMK107CG180JZ P100 1 USB B right-angle connector 4.7F 20%, 6.3V X5R ceramic P101, P102 0 Not installed capacitor (0805) C110 1 TDK C2012X5R0J475M P1 1 5-pin header Taiyo Yuden JMK212BJ475MG P2 1 2 x 5-pin header 0.01F 10%, 50V X7R ceramic P3 1 11-pin header capacitor (0603) C111 1 P4 1 9-pin header TDK C1608X7R1H103K P5 1 4-pin header Taiyo Yuden UMK107B103KZ Maxim Integrated Products 1 For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxims website at www.maxim-ic.com.MAX16031 Evaluation Kit Component List (continued) DESIGNATION QTY DESCRIPTION DESIGNATION QTY DESCRIPTION npn bipolar transistors Maxim dual, low-noise, low- Q1, Q2 2 Fairchild MMBT3904 U100 1 dropout linear regulator Diodes Inc. MMBT3904-7-F MAX8882EUTAQ+ (6-pin SOT23) R1R7, Maxim USB peripheral controller 11 221 1% resistors (0805) U101 1 R100R103 MAX3420EECJ+ (32-pin LQFP) R8R14, R104 8 10k 1% resistors (0805) Maxim microcontroller U102 1 MAXQ2000-RAX+ (68-pin QFN-EP*) R23, R112 0 Not installed, resistors R105, R106 2 33.2 1% resistors (0805) 12MHz crystal (HCM49) Y100 1 Citizen HCM49-12.000MABJ-UT R108, R109, R110 3 4.75k 1% resistors (0805) S1, S2, S3 3 8-row DIP switches Y101 0 Not installed, 32kHz crystal Maxim EEPROM-based system 20MHz crystal (HCM49) Y102 1 U1 1 monitor Citizen HCM49-20.000MABJ-UT MAX16031ETM+ (48-pin TQFN) 5 Shunts Maxim octal 12-bit voltage-output USB high-speed A-to-B cable, DAC with serial interface U2 1 1 5ft (1.5m) MAX5306EUE+ (16-pin TSSOP) 1 PCB: MAX16031 Evaluation Kit+ Maxim precision, low-dropout, U3 1 micropower voltage reference *EP = Exposed paddle. MAX6025AEUR+ (3-pin SOT23) Component Suppliers SUPPLIER PHONE WEBSITE Diodes, Inc. 805-446-4800 www.diodes.com Fairchild Semiconductor 888-522-5372 www.fairchildsemi.com KEMET Corp. 864-963-6300 www.kemet.com Taiyo Yuden 800-348-2496 www.t-yuden.com TDK Corp. 847-390-4373 www.component.tdk.com Note: Indicate that you are using the MAX16031 when contacting these component suppliers. 2) Connect the MAX16031 EV kit to a PC using the Quick Start USB cable provided with the EV kit. LED100 will Required Equipment light indicating that the EV kit has power. Before beginning, the following equipment is needed: 3) Install the EV kit software. MAX16031 EV kit (includes USB cable) 4) Launch MAX16031.exe. A user-supplied PC with a spare USB port 5) Click the I2C radio button in the Connect dialog Note: In the following sections, software-related items box, and make sure Address is 0x18. Press the OK are identified by bolding. Text in bold refers to items button. directly from the EV kit software. 6) Click the number 0.00 next to DAC Voltage for IN1. Procedure 7) In the Set Input Voltage dialog box, enter 1.00 and The MAX16031 EV kit is fully assembled and tested. press the OK button. Follow the steps below to verify board operation: 8) Note that the voltage in the chart-recorder view 1) Make sure jumpers J1 and J2 are in the 0 position, J3 increases to 1V. is closed, J100 is in the 3.3V position, and J4 is in the 1-2 position. Also ensure that all switches in switch banks S1, S2, and S3 are all in the ON position. 2 Evaluates: MAX16031