19-5864 Rev 0 5/11 MAX16065 Evaluation Kit Evaluates: MAX16065 General Description Features The MAX16065 evaluation kit (EV kit) provides a proven S USB Interface to Host PC PCB layout that facilitates evaluation of the MAX16065 S Easy-to-Use GUI Software flash-configurable system manager with nonvolatile fault S On-Board Loopback Switches for Stand-Alone memory. The EV kit is a fully assembled and tested Evaluation surface-mount board. S On-Board Potentiometers to Simulate Fault The EV kit includes an on-board USB-to-JTAG and Conditions SMBus interface, facilitating communications between S Convenient Test Points and Headers for Easy the host PC and the device. Two potentiometers and a set of loopback switches make it easy to evaluate Evaluation the sequencing and monitoring functions of the device S Proven PCB Layout without requiring external power supplies. Headers are S Fully Assembled and Tested also provided to facilitate connection to an external application circuit. Ordering Information appears at end of data sheet. This EV kit data sheet assumes basic familiarity with the device. Refer to the MAX16065/MAX16066 IC data sheet for more detailed information. EV Kit Contents List QTY DESCRIPTION 1 Circuit board assembly: MAX16065EVKIT+ 1 USB high-speed A-to-mini B cable, 5ft (1.5m) Component List DESIGNATION QTY DESCRIPTION DESIGNATION QTY DESCRIPTION 0.1FF Q10%, 25V X7R ceramic 1FF Q20%, 16V X5R ceramic C1, C2, C3, 7 capacitors (0603) C20 1 capacitor (0603) C16C19 TDK C1608X7R1E104K TDK C1608X5R1C105K 17.1V zener diodes (3 SOT23) 1FF Q10%, 6.3V X5R ceramic D1, D2 2 Central Semi CMPZ5248B+ C4, C13, C15 3 capacitors (0603) TDK C1608X5R0J105K EXT PWR 1 Red PC-mount test point F1 1 500mA fuse (2405) 18pF Q5%, 50V C0G ceramic C5C8 4 GND 1 Black PC-mount test point capacitors (0603) TDK C1608C0G1H180J J1 1 6-pin header J2 1 2-pin header 2.2FF Q10%, 6.3V X5R ceramic C9, C10 2 capacitors (0603) J3 1 8-pin header TDK C1608X5R0J225K J4 1 3-pin header LED1LED13 13 Green LEDs 4.7FF Q10%, 6.3V X5R ceramic C11 1 capacitor (0603) P1 1 USB mini-B connector TDK C1608X5R0J475K P2 0 Not installed, 8-pin header P3 0 Not installed, 10-pin header 0.01FF Q10%, 50V X7R ceramic C12 1 capacitor (0603) Dual-row, 10-pin protected P4 1 TDK C1608X7R1H103K header P5 1 5-pin header 10FF Q20%, 16V X5R ceramic C14 1 capacitor (1206) P6 1 15-pin header TDK C3216X5R1C106M P7 1 12-pin header Maxim Integrated Products 1 For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxims website at www.maxim-ic.com.MAX16065 Evaluation Kit Evaluates: MAX16065 Component List (continued) DESIGNATION QTY DESCRIPTION DESIGNATION QTY DESCRIPTION P8 1 13-pin header Microcontroller (56 TQFN-EP) U1 1 Maxim MAXQ2000-RBX+ n-channel MOSFETs Q1, Q2 2 Fairchild FDC5612 USB peripheral controller R1, R2, R3 3 4.75kI Q1% resistors (0603) U2 1 (24 TQFN-EP) Maxim MAX3420EETG+ R4, R5, R6, 5 221I Q1% resistors (0603) R10, R12 Dual, low-noise, LDO linear R7, R13 2 10kI Q1% resistors (0603) U3 1 regulator (6 SOT23) Maxim MAX8882EUTAQ+ R8, R9 2 33.2I Q1% resistors (0603) R11 0 Not installed, resistor (2512) 12-channel flash-configurable R14 1 11kI Q1% resistor (0805) system manager with nonvolatile U4 1 fault registers (48 TQFN-EP) R15, R16 2 5kI slide potentiometers, 30mm Maxim MAX16065ETM+ R17, R18, R19 3 10kI Q1% resistors (0805) RP1 1 8 x 220I Q5% resistor array Y1 1 12MHz crystal (HCM49) RP2 1 8 x 10kI Q5% resistor array Y2 1 20MHz crystal (HCM49) S1S6 6 8-position DIP switches 4 Shunts S7 1 SPST pushbutton switch 1 MAX16065 EVALUATION KIT+ S8, S9 2 SPDT slide switches Component Suppliers SUPPLIER PHONE WEBSITE Central Semiconductor 631-435-1110 www.centralsemi.com Fairchild Semiconductor 888-522-5372 www.fairchildsemi.com TDK Corp. 847-803-6100 www.component.tdk.com Note: Indicate that you are using the MAX16065 when contacting these component suppliers. in switch banks S1 and S2 should be in the on position. Quick Start All switches in switch banks S3 (EXT SEL), S4 (PC SEL), and S5 (PULLUP) should be in the on position. Required Equipment Switch bank S6 switches 1 and 8 should be in the on MAX16065 EV kit position, but all other switches should be off. User-supplied PC with a spare USB port 3) Connect the EV kit to a PC using the provided USB Note: In the following sections, software-related items cable. LED4 lights to indicate that the EV kit has are identified by bolding. Text in bold refers to items power. directly from the EV kit software. 4) Install and launch the EV kit software. Procedure 5) Select I2C from the Connection menu. Make sure that The EV kit is fully assembled and tested. Follow the steps Address is 0xA0 in the Address dialog box. Click OK. below to verify board operation: 6) From the File menu, select Open 1) Make sure that jumper J1 (VCC SEL) is in the 5.0V 7) Select the MAX16065 EV Kit Demo.hex file located position. Also make sure that jumper J2 (CSBIAS) in the software install folder and click OK. This action is closed, jumper J3 (I2C ADDR) is set to low, and loads the device registers (but not the flash memory) jumper J4 (MON1-2 SE/DIFF) is in the 1-2 position with the demo configuration. (single ended). 8) Click on the Datalogging tab. Move the enable switch 2) Switches 1 and 2 in switch bank S1 (EN MON loop- (S9) to the on position and note the monitored voltages. backs) should be in the off position. All other switches Maxim Integrated Products 2